Hot Racing 9.5G Brass Kmc Machete Wheel Weights, For Axial Scx24

9.5g Brass KMC Machete Wheel Weights, for Axial SCX24

Hot Racing front or rear wheel weights for the stock 1.0in KMC Machete wheels on the Axial SCX24.

Features:

CNC machined solid brass billet

9g each fitted to the wheels to decrease the lorries center of mass, increase its stability, enhance climbing up, reduce the opportunity for turning in reverse, and make for a general more capable spider|spider}

Friction fit to within KMC Machete wheels. Some CA glue can be utilized to protect setup

Can be utilized either in front of rear, however if you're only getting one set we advise using them in the front

Specs:

Center: 12mm hex

For : AXI31615

Diameter of outer : 21.4mm

Diameter of within : 12mm

Weight: 9.5g/ea

Width: 8mm

Regularly purchased with the product that you are currently reading about.

9G Brass Differential Cover, For Axial Scx24

9g Brass Differential Cover, for Axial SCX24

Hot Racing heavy brass cover for SCX24 Worm gear Axles Adds 9g of weight to the axle in a low and centralized area to decrease the automobile's center of gravity, increase its stability, and make it an overall more capable crawler.

Features:

CNC machined solid brass billet

Adds 9g of low and main weight to lower and centralize the automobile's center of mass, increase its stability, and make it an

Overall more capable crawler

mm increased density over stock cover for additional durability and weight

Fits either the front or rear

Specs:

Width:14.33 mm

Height:24 mm

Weight: 9g

Want one more terrific product to match the above mentioned product?

Brass Front Steering Knuckle, For Axial Scx24

Brass Front Steering Knuckle, for Axial SCX24

Hot Racing strong brass SCX24 Worm gear Axles guiding knuckles (guiding blocks) for the Axial SCX24 axles. Add weight to your crawler where it needs it - down low.

Features:

CNC machined solid brass

Heavy to include weight to automobile for higher stability and lower CG

Cutouts on knuckle for access to outer bearing race for easy bearing elimination

Direct replacement for factory plastic guiding knuckles

Want one more terrific product to match the above mentioned product?

Brass Stock Wheels Hub, 7Mm Hex, For Scx24

Brass Stock Wheels Center, 7mm Hex, for SCX24

Features:

CNC Machined Solid Brass construction.

You Will Receive:

Four Hex Wheel Hubs

Four 2 x 6mm Axle Pins

Requirements:

Assembly onto SCX24.

Specs:

Hex: 7mm

Inner diameter: 4mm

Right here is a terrific product that lots of others have actually bought at the very same time.

Aluminum Front Bumper W/Fairlead And Light Buckets, For Axial Sc

Aluminum Front Bumper w/Fairlead and Light Containers, for Axial SCX24

Hot Racing CNC machined aluminum front bumper with 3mm LED light pails, winch fairlead for use with Axial SCX 24.

Features:

Billet CNC machined aluminum

Anodized an elegant flat black

Integrated brush guards

Light pails for 3mm LED lights

Specs:

Width: 58mm

Height: 8mm

Right here is a terrific product that lots of others have actually bought at the very same time.

SCX24 Deadbolt 1/24th Scale Elec 4WD - RTR, Red

Key Features:
• Includes radio system, ESC and transmitter batteries
• Includes motor and on-board LiPo battery
• Reasonable narrow-stance rock crawler body in olive green or red
• Molded roll cage with realistic light bar
• Reasonable motorist figure and many other scale details
• Officially certified KMC XD229 Machete Crawl wheels
• Officially certified Nitto Path Grappler M/T tires (S30 substance, big block tread)
• Full-time 4WD
• Splined and sleeved front and rear drive shafts permit maximum suspension travel while keeping the power to the wheels
• Steel front and rear axles, front stub axles and dogbones provide strength and toughness
• Rugged steel C-channel frame rails with bracing keep whatever rigid and lined up
• Front and rear axles include a two-piece, molded plastic solid axle design
• 3-Link front and 4-link rear suspension supply optimal handling
• Coil-over shocks with simulated reservoir and resilient plastic suspension links provide proven Axial crawling efficiency
• Front and rear differentials each house a worm gear setup to power the axles and produce greater ground clearance. Worm gear drive likewise supplies a low gear ratio to reduce torque twist
• Two LEDs in the front bumper for night driving
The SCX24™ Deadbolt™ 4WD is the very first Axial® off-roader in 1/24 scale. At less than 8” long, it’s the perfect rig to take along on your hiking, camping, and other outdoor and indoor adventures — offering factory-assembled ease, scale looks, and positive handling on any trail.

Even brand-new modelers driving the SCX24 chassis will be fully equipped to deal with tough climbs and rough trails. Like the larger SCX10™ chassis, this smaller sized variation utilizes a lot of steel elements — from the C-channel frame rails to the front and rear axles and dogbones. Even over off-road, mountainous, rocky and desert terrain, it has the strength to keep pressing onward and upward.

For the most reputable handling, the SCX24 chassis includes a three-link front and four-link rear suspension. The mix of coil-over shocks and resilient plastic suspension links delivers Axial-worthy crawling efficiency even at this little scale. The worm gear drive setup allows a high ground clearance plus a low gear ratio that lowers torque twist.

Powered by a consisted of 180-size motor and LiPo battery, the SCX24 Deadbolt flaunts skills and charm on the trails. Check out that Deadbolt body — with its narrow stance, bulging hood, realistic motorist figure, and molded roll cage with realistic light bar. The realism continues right down to the ground, where you’ll find certified KMC XD229 Machete Crawl wheels covered in Nitto Path Grappler tires.

Adding even more to its newbie appeal, the SCX24 Deadbolt comes 100% complete and prepared to run. Whatever required for action remains in the box: put together and ended up automobile; Axial 2-channel 2.4GHz radio system with servo and ESC/receiver system; Dynamite® 88T brushed electrical motor and 350mAh TWO 7.4V LiPo battery; USB LiPo charger; and even 4 AA cells for the transmitter!

What's in package?
(1) SCX24™ Deadbolt™ 1/24 Scale 4WD Truck
    (1) Axial AE-6 ESC/receiver combination (installed)
    (1) Dynamite® 88T brushed electrical motor (installed)
    (1) Axial AS-1 guiding servo (installed)
(1) Axial® AX-4 2.4GHz 2-channel radio
(4) AA transmitter batteries
(1) 350mAh TWO 7.4V LiPo battery
(1) USB LiPo charger
(1) Item Manual




STEEL C-CHANNEL CHASSIS FRAME RAILS
Much like the 1/10th scale SCX10™ platform, the SCX24™ chassis functions rugged and tough steel c-channel frame rails with bracing to keep whatever undamaged and lined up.
 

DYNAMITE® 88T BRUSHED MOTOR
The Dynamite 88T brushed electrical motor supplies the right amount of torque to help ascend high climbs. It's mated to a steel motor mount to keep flex to a minimum, which helps safeguard the equipments.
 


WORM GEARS
The front and rear differentials each house a worm screw and worm gear setup to get the power to the axles and produce greater ground clearance.
 

DURABLE STEEL AXLES
Steel front and rear axles, front stub axles in addition to steel dogbones provide strength and toughness to keep things running during tough climbs and rough trails.
 


SPLINED DRIVE SHAFTS
The front and rear drive shafts are splined and sleeved to permit maximum suspension travel while keeping the power to the wheels.
 

COILOVER SHOCK ABSORBERS
Even at this little scale, the mix of coilover shocks with simulated tanks and resilient plastic suspension links delivers the crawling efficiency you've understood and expect from Axial.
 


FRONT AND REAR SOLID AXLES
The front and rear axles include a two piece, formed plastic solid axle design. For optimal handling, the SCX24™ suspension includes a three-link front and four-link rear setup.
 


LED LIGHTS INCLUDED
Two brilliant LED lights are included and are installed in the front bumper. An additional LED light port on the ESC permits you to include optional LED lights.
 

4-LINK REAR SUSPENSION
The suspension geometry makes use of a 4-Link design for the rear which is enhanced to reduce axle steer and torque twist. We've likewise included extra suspension links for changing your wheelbase length.
 


KMC XD229 MACHETE CRAWL WHEELS & NITTO TRAIL GRAPPLER M/T TIRES
Officially certified KMC XD Machete wheels are legendary in the off-road world. They are formed in black and function sensational scale details, in spite of the little scale.
The officially accredited Nitto Path Grappler M/T Tires provide a fantastic mix of off-road efficiency while still maintaining exceptional composure for on-road use.
 

HINGED BODY SYSTEM
The hinged body system uses easy access to on-board elements. You can rapidly reach the battery and chassis by removing simply 2 body clips and swinging the body up.
 


FULL BALL BEARINGS
Just because the SCX24™ is smaller sized in size doesn't imply the functions need to follow suit. No bushings discovered here, rather the drivetrain is freely spinning on sealed cartridge bearings throughout the entire automobile.
 

AXIAL AS-1 SERVO
Mounted simply above the front axle is the Axial AS-1 servo, with a servo saver that permits guiding precision, while likewise providing protection for the servo equipments in case of a bind or effect.
 

Specs

Type: Crawler
Scale: 1/24
Length: 7.8" (199.5mm)
Width: 3.9" (99.5mm)
Height: 4.73" (120.2mm)
Ground Clearance: 1.06" (27mm)
Wheepoundase: 5.25" (133.5mm)
Weight: 0.5lb (0.22kg)
Chassis: Stamped steel rails
Suspension: Solid axle, front and rear
Drivetrain: 4WD
Tire Type: Nitto Path Grappler M/T, big block tread
Speed Control: AE-6 ESC receiver/combo
Radio: AX-4 2.4GHz 2-channel
Servos: AS-1 steering servo
Batteries: 7.4V 350mAh 30C LiPo (included)
Charger: USB LiPo charger (included)
Equipment Pitch: 32-Pitch
Wheel Size: 0.48" (12.4mm) width, 1.0" (26mm) diameter
Kit/RTR: RTR
Shock Type: Plastic body coil-over .9 - 1.3" (24 - 33.4mm)
Body: Painted and trimmed Axial Deadbolt
Ball Bearings: Complete body
Is Assembly Required: No