JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V (Hitec 31055S | HRC31055S)
Due to the impact of the COVID-19/Corona virus, there my be delays in the shipping estimates shown on our site.

We appreciate your understanding and support during these uncertain times.

Top Seller

Model: Hitec 31055S
Dist. #: HRCM0982   SKU: HRC31055S

Be the first to review this product. (Write Review)

Shipping: In Stock For Shipping
Store Pickup:

South Jordan, UT
Available Now!

List Price:  $19.95
Price:  $13.49
You Save:  $6.46 (32%)

This item will earn you 13 reward point(s).
13 points = $0.26 off your next order. Learn More

Updated on Jul 29, 2021 11:02:43 AM

HS-55 Servo Economy Sub Micro Univ...
    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and lightweight for mounting in little aircrafts,
    electrics or gliders, where very high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train provides reputable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One very little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
Two M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is often purchased with the above stated item.



This is the Futaba S3003 Standard Servo.
This fundamental servo is used in automobiles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, ensure they are capable
of providing sufficient amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangular rubber grommets (FUTM2348)
4 servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year guarantee

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Often purchased with the item that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building minimizes rotating mass for
    greater output and longer life.
Reinforcing carbon fibers assist keep true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring instruction sheet

REQUIRES:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Glow engines

The below item likewise pairs really well with the item being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon building minimizes rotating mass for
    greater output and longer life
Created for electrical powered Park Leaflet type aircraft with rear
    dealing with motors that "push" the airplane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    instruction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center size: 0.50"
Hole Size: 1/4"

REQUIRES:
Only for use with electrical motors. Not for use with glow or gasoline
    engines.
All props require balancing, this is ESSENTIAL, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

Frequently Bought Together

Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V
+
Futaba S3003 Standard Servo .19Sec/56.9Oz @ 6V
This Item: Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V
$13.49
Futaba S3003 Standard Servo .19Sec/56.9Oz @ 6V
$10.99

Total Price: $24.48

Add Both To Cart

Customers who bought this product also purchased

Visual Parts Finder
";