Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and light-weight for mounting in little planes,
    electrics or gliders, where very high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train provides reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One very little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is often purchased with the above mentioned item.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is utilized in cars, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of delivering adequate amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangle-shaped rubber grommets (FUTM2348)
4 servo install screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon gears
One year warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Connector: "J" type with approx. 5" lead

Regularly purchased with the item that you are presently reviewing.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building minimizes turning mass for
    higher output and longer life.
Reinforcing carbon fibers help keep real, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring direction sheet

NEEDS:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines

The listed below item additionally pairs really well with the item being gone over.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Lightweight molded nylon building minimizes turning mass for
    higher output and longer life
Developed for electric powered Park Leaflet type aircraft with rear
    facing motors that "push" the plane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    direction sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center diameter: 0.50"
Hole Diameter: 1/4"

NEEDS:
Just for use with electric motors. Not for use with radiance or gasoline
    engines.
All props need balancing, this is CRUCIAL, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)