Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and light-weight for installing in little airplanes,
    electrics or gliders, where very high speed and excellent torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train provides reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One very little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is frequently acquired with the above stated item.



This is the Futaba S3003 Standard Servo.
This basic servo is utilized in vehicles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make certain they are capable
of providing adequate amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year guarantee

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Often acquired with the item that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building decreases turning mass for
    greater output and longer life.
Reinforcing carbon fibers help keep true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not created for Glow engines

The below item additionally pairs actually well with the item being discussed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Light-weight molded nylon building decreases turning mass for
    greater output and longer life
Developed for electric powered Park Leaflet type airplane with rear
    facing motors that "push" the aircraft forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    guideline sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Thickness: 0.30" Hub size: 0.50"
Hole Size: 1/4"

REQUIRES:
Just for usage with electric motors. Not for usage with radiance or fuel
    engines.
All props require balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)