Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and light-weight for mounting in small planes,
    electrics or gliders, where very high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train offers reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One very small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is frequently gotten with the above mentioned item.



This is the Futaba S3003 Standard Servo.
This fundamental servo is used in vehicles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of providing enough amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo install screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon equipments
One year warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Regularly gotten with the item that you are presently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction reduces rotating mass for
    greater output and longer life.
Reinforcing carbon fibers assist preserve true, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring direction sheet

NEEDS:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Radiance engines

The below item likewise pairs actually well with the item being discussed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Lightweight molded nylon construction reduces rotating mass for
    greater output and longer life
Designed for electric powered Park Leaflet type aircraft with rear
    facing motors that "push" the plane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with 2 locating rings and
    direction sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center size: 0.50"
Hole Size: 1/4"

NEEDS:
Only for use with electric motors. Not for use with radiance or gas
    engines.
All props require balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)