Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and lightweight for installing in small aircrafts,
    electrics or gliders, where really high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train provides reputable operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One really small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This product is regularly gotten with the above stated product.



This is the Futaba S3003 Standard Servo.
This standard servo is utilized in automobiles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of providing enough amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon equipments
One year service warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Regularly gotten with the product that you are presently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building reduces rotating mass for
    greater output and longer life.
Reinforcing carbon fibers assist preserve real, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring guideline sheet

NEEDS:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines

The below product additionally pairs actually well with the product being gone over.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Light-weight molded nylon building reduces rotating mass for
    greater output and longer life
Developed for electric powered Park Leaflet type aircraft with rear
    facing motors that "push" the plane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with 2 finding rings and
    guideline sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Thickness: 0.30" Hub diameter: 0.50"
Hole Diameter: 1/4"

NEEDS:
Only for use with electric motors. Not for use with glow or gasoline
    engines.
All props require balancing, this is ESSENTIAL, use TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)