Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and light-weight for installing in little airplanes,
    electrics or gliders, where very high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train offers dependable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One very little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
Two M1.7x7 servo installing screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This thing is often bought with the above mentioned thing.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is used in automobiles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of delivering enough amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangle-shaped rubber grommets (FUTM2348)
4 servo mount screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Often bought with the thing that you are currently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building reduces rotating mass for
    greater output and longer life.
Reinforcing carbon fibers help keep true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

NEEDS:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not designed for Glow engines

The below thing additionally pairs really well with the thing being discussed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Light-weight molded nylon building reduces rotating mass for
    greater output and longer life
Designed for electrical powered Park Flyer type aircraft with rear
    dealing with motors that "push" the airplane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with 2 finding rings and
    instruction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Density: 0.30" Hub diameter: 0.50"
Hole Size: 1/4"

NEEDS:
Only for usage with electrical motors. Not for usage with radiance or gasoline
    engines.
All props require balancing, this is CRUCIAL, utilize TOPQ5700.
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)