Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and light-weight for installing in small planes,
    electrics or gliders, where really high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train offers trustworthy operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One really small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This thing is regularly purchased with the above pointed out thing.



This is the Futaba S3003 Requirement Servo.
This basic servo is utilized in automobiles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make sure they are capable
of providing sufficient amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangular rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon gears
One year service warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Regularly purchased with the thing that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building minimizes rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist keep real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring guideline sheet

REQUIRES:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not designed for Glow engines

The below thing additionally sets truly well with the thing being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Lightweight molded nylon building minimizes rotating mass for
    higher output and longer life
Designed for electric powered Park Flyer type aircraft with rear
    facing motors that "push" the aircraft forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two finding rings and
    guideline sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Thickness: 0.30" Hub size: 0.50"
Hole Size: 1/4"

REQUIRES:
Just for use with electric motors. Not for use with radiance or gasoline
    engines.
All props require balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)