Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and lightweight for installing in small aircrafts,
    electrics or gliders, where very high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train provides trusted operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One very small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This product is regularly acquired with the above pointed out product.



This is the Futaba S3003 Requirement Servo.
This standard servo is utilized in cars, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, ensure they are capable
of delivering adequate amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangular rubber grommets (FUTM2348)
Four servo install screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon gears
One year service warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Connector: "J" type with approx. 5" lead

Frequently acquired with the product that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building reduces rotating mass for
    greater output and longer life.
Reinforcing carbon fibers help maintain true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring direction sheet

NEEDS:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines

The listed below product also sets actually well with the product being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Lightweight molded nylon building reduces rotating mass for
    greater output and longer life
Designed for electric powered Park Leaflet type airplane with rear
    facing motors that "push" the plane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with two finding rings and
    direction sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center size: 0.50"
Hole Size: 1/4"

NEEDS:
Just for usage with electric motors. Not for usage with glow or fuel
    engines.
All props need balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)