Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and lightweight for mounting in little planes,
    electrics or gliders, where very high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train supplies trustworthy operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One very little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This product is frequently bought with the above mentioned product.



This is the Futaba S3003 Requirement Servo.
This basic servo is utilized in automobiles, boats, or where conventional servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of providing enough amps.

INCLUDES:
One S3003 conventional servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangular rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon gears
One year warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Often bought with the product that you are presently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building and construction decreases turning mass for
    greater output and longer life.
Reinforcing carbon fibers assist preserve true, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring instruction sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Radiance engines

The below product likewise pairs really well with the product being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon building and construction decreases turning mass for
    greater output and longer life
Developed for electric powered Park Leaflet type aircraft with rear
    dealing with motors that "push" the aircraft forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    instruction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center size: 0.50"
Hole Size: 1/4"

REQUIRES:
Just for usage with electric motors. Not for usage with glow or fuel
    engines.
All props need balancing, this is CRUCIAL, utilize TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)