Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Equipment Micro Servo from Hitec.

FEATURES:
For small airplanes, gliders, electric helicopters and 1/18 scale cars

SUCHES AS:
HS-82MG Metal Equipment Micro Servo with universal connector, 0.67" (17mm)
    diameter horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and mounting hardware

NEEDS:
Setting up in model and connecting to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are readily available;
Equipment Set, HRCM6386
Horn Set, HRCM6326

Want another excellent item to enhance the above mentioned item?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high performance aircrafts. Delivering
45A of continuous present with an integrated Battery Circuit
which can handle 2A, this ESC is easy to utilize
and extremely affordable.

FEATURES:
Compatible with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz changing frequency, for good run time and cool operation
Pre-installed Universal radio connector* (see Remarks listed below)
Pre-installed WS Deans Ultra male connector for battery (see
Remarks listed below)
Pre-installed gold plated 4mm female bullet ports for motor
High powered changing BEC (Battery Remover Circuit) which
    handles 3 or 4 basic servos
Complete proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see information in Remarks listed below)
Thermal Security stops motor when maximum temperature level 230°F
    is reached
180 Day Warranty (USA & Canada Just)

SUCHES AS:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver connector, battery connector, and motor
    ports.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery connector, use: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Current: 45A continuous maximum
50A surge maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Running frequency: 16kHz repaired
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To utilize with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle stick to full throttle position,
then to "OFF" position, then slowly advance throttle and motor will
start to run.

The "Silver Series" line of brushless electronic speed controls
    include numerous built-in security features. One such feature COULD
    PERHAPS TRIGGER THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an incredibly low position and/or if
    rotation of the brushless motor is restrained or blocked in some
    way. This is NORMAL, as the ESC is discovering that an issue
    potentially exists with the motor and/or speed control. Rotation of
    the motor is stopped to secure the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually already been equipped and the motor has been
turning usually, yet after moving the throttle stick to near minimum the
motor suddenly stops to turn usually even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD LEAD TO PERSONAL INJURY!! From this point, moving
the throttle stick up - even to full throttle might not trigger the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To gain back
control of the motor, move the throttle stick to outright minimum throttle
position then advance the throttle stick up-wards when again.
Alternatively, you can detach the battery from the ESC, then re-connect the
source of power and re-arm the system.
NEVER
get near the propeller if the speed control is connected to input power!
ALWAYS
ensure the throttle stick is at minimum position before trying to
detach the battery from the speed control! ElectriFly is not accountable
for incidental damage or accident as an outcome of misuse of this item.