Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small airplanes, gliders, electric helicopters and 1/18 scale cars

INCLUDES:
HS-82MG Metal Gear Micro Servo with universal connector, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

NEEDS:
Installing in design and linking to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

COMMENTS:
The following replacement parts are offered;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want one more great thing to enhance the above stated thing?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency planes. Delivering
45A of constant present with an integrated Battery Circuit
which can deal with 2A, this ESC is simple to use
and extremely affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz changing frequency, for great run time and cool operation
Pre-installed Universal radio connector* (see Remarks listed below)
Pre-installed WS Deans Ultra male connector for battery (see
Remarks listed below)
Pre-installed gold plated 4mm female bullet ports for motor
High powered changing BEC (Battery Remover Circuit) which
    handles 3 or 4 conventional servos
Complete proportional forward and smooth throttle response with ON/OFF
    brake
Safe Start System** (see information in Remarks listed below)
Thermal Security stops motor when optimum temperature 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Just)

INCLUDES:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver connector, battery connector, and motor
    ports.

REQUIRES:
Mating motor connectors, usage: GPMM3114
Mating battery connector, usage: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Current: 45A constant optimum
50A surge optimum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz fixed
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

COMMENTS:
To use with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle adhere to complete throttle position,
then to "OFF" position, then gradually advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
    such as numerous integrated safety functions. One such function COULD
    POSSIBLY TRIGGER THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an exceptionally low position and/or if
    rotation of the brushless motor is restrained or obstructed in some
    method. This is NORMAL, as the ESC is spotting that a problem
    perhaps exists with the motor and/or speed control. Rotation of
    the motor is stopped to protect the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually currently been armed and the motor has been
turning normally, yet after moving the throttle adhere to near minimum the
motor all of a sudden stops to rotate normally even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD RESULT IN PERSONAL INJURY!! From this point, moving
the throttle hold up - even to complete throttle may not cause the motor to
rotate BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To gain back
control of the motor, move the throttle adhere to outright minimum throttle
position and then advance the throttle stick upwards as soon as again.
Alternatively, you can detach the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
get near the propeller if the speed control is connected to input power!
ALWAYS
make certain the throttle stick is at minimum position before trying to
detach the battery from the speed control! ElectriFly is not responsible
for incidental damage or accident as a result of abuse of this product.