Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For little planes, gliders, electric helicopters and 1/18 scale vehicles

SUCHES AS:
HS-82MG Metal Gear Micro Servo with universal port, 0.67" (17mm)
    diameter horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

NEEDS:
Setting up in model and linking to receiver

SPECIFICATIONS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

COMMENTS:
The following replacement parts are available;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want an additional wonderful item to compliment the above stated item?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency planes. Providing
45A of continuous current with an integrated Battery Circuit
which can deal with 2A, this ESC is easy to utilize
and really affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz changing frequency, for great run time and cool operation
Pre-installed Universal radio port* (see Remarks below)
Pre-installed WS Deans Ultra male port for battery (see
Remarks below)
Pre-installed gold plated 4mm female bullet adapters for motor
High powered changing BEC (Battery Eliminator Circuit) which
    deals with 3 or 4 standard servos
Full proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see information in Remarks below)
Thermal Protection stops motor when maximum temperature level 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Just)

SUCHES AS:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver port, battery port, and motor
    adapters.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery port, use: WSDM3000

SPECIFICATIONS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Present: 45A continuous maximum
50A surge maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz fixed
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

COMMENTS:
To utilize with "Old Airtronics" Rx, requires adapter: AIRM4400

**Safe Start System: Move throttle stick to complete throttle position,
then to "OFF" position, then slowly advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
    include many built-in security features. One such function COULD
    PERHAPS TRIGGER THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an extremely low position and/or if
    rotation of the brushless motor is restrained or obstructed in some
    method. This is NORMAL, as the ESC is spotting that an issue
    possibly exists with the motor and/or speed control. Rotation of
    the motor is stopped to secure the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually currently been armed and the motor has been
rotating typically, yet after moving the throttle stick to near minimum the
motor all of a sudden stops to turn typically even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD LEAD TO PERSONAL INJURY!! From this point, moving
the throttle hold up - even to complete throttle might not trigger the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To restore
control of the motor, move the throttle stick to outright minimum throttle
position and after that advance the throttle stick upwards when again.
Alternatively, you can detach the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
come up to the propeller if the speed control is connected to input power!
ALWAYS
make certain the throttle stick is at minimum position prior to trying to
detach the battery from the speed control! ElectriFly is not responsible
for incidental damage or injury as an outcome of misuse of this item.