Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small aircrafts, gliders, electrical helicopters and 1/18 scale automobiles

INCLUDES:
HS-82MG Metal Gear Micro Servo with universal port, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and mounting hardware

NEEDS:
Setting up in design and linking to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are available;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want another excellent item to match the above stated item?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency planes. Providing
45A of constant current with a built-in Battery Circuit
which can manage 2A, this ESC is basic to use
and really affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for excellent run time and cool operation
Pre-installed Universal radio port* (see Remarks listed below)
Pre-installed WS Deans Ultra male port for battery (see
Remarks listed below)
Pre-installed gold plated 4mm female bullet connectors for motor
High powered switching BEC (Battery Eliminator Circuit) which
    handles 3 or 4 basic servos
Complete proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see information in Remarks listed below)
Thermal Defense stops motor when maximum temperature level 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Only)

INCLUDES:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver port, battery port, and motor
    connectors.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery port, use: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Present: 45A constant maximum
50A rise maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Running frequency: 16kHz repaired
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To use with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle stick to complete throttle position,
then to "OFF" position, then gradually advance throttle and motor will
start to run.

The "Silver Series" line of brushless electronic speed controls
    include many built-in security functions. One such feature COULD
    PERHAPS CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an exceptionally low position and/or if
    rotation of the brushless motor is restrained or blocked in some
    method. This is NORMAL, as the ESC is spotting that a problem
    potentially exists with the motor and/or speed control. Rotation of
    the motor is stopped to safeguard the speed control from possible
    damage.
WARNING!!
If the ESC and motor have currently been armed and the motor has been
rotating typically, yet after moving the throttle stick to near minimum the
motor all of a sudden ceases to turn typically even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS CAUTION COULD LEAD TO INJURY!! From this point, moving
the throttle hold up - even to complete throttle may not trigger the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To restore
control of the motor, move the throttle stick to absolute minimum throttle
position and then advance the throttle stick upwards once again.
Alternatively, you can detach the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
get near the propeller if the speed control is connected to input power!
ALWAYS
make certain the throttle stick is at minimum position before trying to
detach the battery from the speed control! ElectriFly is not accountable
for incidental damage or injury as an outcome of misuse of this item.