Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small aircrafts, gliders, electric helicopters and 1/18 scale automobiles

SUCHES AS:
HS-82MG Metal Gear Micro Servo with universal connector, 0.67" (17mm)
    diameter horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

NEEDS:
Setting up in design and linking to receiver

SPECIFICATIONS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

COMMENTS:
The following replacement parts are offered;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want one more wonderful item to match the above discussed item?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high performance aircrafts. Delivering
45A of continuous present with a built-in Battery Circuit
which can manage 2A, this ESC is easy to use
and extremely affordable.

FEATURES:
Compatible with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for great run time and cool operation
Pre-installed Universal radio connector* (see Remarks below)
Pre-installed WS Deans Ultra male connector for battery (see
Remarks below)
Pre-installed gold plated 4mm female bullet connectors for motor
High powered switching BEC (Battery Eliminator Circuit) which
    manages 3 or 4 basic servos
Complete proportional forward and smooth throttle response with ON/OFF
    brake
Safe Start System** (see details in Remarks below)
Thermal Defense stops motor when maximum temperature level 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Just)

SUCHES AS:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver connector, battery connector, and motor
    connectors.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery connector, use: WSDM3000

SPECIFICATIONS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Present: 45A continuous maximum
50A surge maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Running frequency: 16kHz fixed
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

COMMENTS:
To use with "Old Airtronics" Rx, requires adapter: AIRM4400

**Safe Start System: Move throttle stick to complete throttle position,
then to "OFF" position, then gradually advance throttle and motor will
start to run.

The "Silver Series" line of brushless electronic speed controls
    include numerous built-in security functions. One such feature COULD
    PERHAPS CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an exceptionally low position and/or if
    rotation of the brushless motor is hindered or blocked in some
    way. This is NORMAL, as the ESC is spotting that a problem
    perhaps exists with the motor and/or speed control. Rotation of
    the motor is stopped to secure the speed control from possible
    damage.
WARNING!!
If the ESC and motor have currently been equipped and the motor has been
turning generally, yet after moving the throttle stick to near minimum the
motor all of a sudden ceases to turn generally even if the throttle stick is advanced
above minimum throttle, DO NOT LOCATION YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD LEAD TO INJURY!! From this point, moving
the throttle hold up - even to complete throttle might not cause the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To restore
control of the motor, move the throttle stick to absolute minimum throttle
position then advance the throttle stick up-wards once again.
Alternatively, you can disconnect the battery from the ESC, then re-connect the
source of power and re-arm the system.
NEVER
come up to the propeller if the speed control is linked to input power!
ALWAYS
make sure the throttle stick is at minimum position prior to trying to
disconnect the battery from the speed control! ElectriFly is not accountable
for incidental damage or injury as an outcome of abuse of this product.