Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small planes, gliders, electric helicopters and 1/18 scale cars

SUCHES AS:
HS-82MG Metal Gear Micro Servo with universal port, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and mounting hardware

REQUIRES:
Setting up in design and linking to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

COMMENTS:
The following replacement parts are offered;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want one more excellent thing to compliment the above mentioned thing?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency planes. Providing
45A of continuous current with an integrated Battery Circuit
which can manage 2A, this ESC is basic to utilize
and extremely affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for great run time and cool operation
Pre-installed Universal radio port* (see Remarks listed below)
Pre-installed WS Deans Ultra male port for battery (see
Remarks listed below)
Pre-installed gold plated 4mm female bullet ports for motor
High powered switching BEC (Battery Eliminator Circuit) which
    manages 3 or 4 basic servos
Complete proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see details in Remarks listed below)
Thermal Security stops motor when optimum temperature 230°F
    is reached
180 Day Warranty (U.S.A & Canada Just)

SUCHES AS:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver port, battery port, and motor
    ports.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery port, use: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Existing: 45A continuous optimum
50A rise optimum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz repaired
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

COMMENTS:
To utilize with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle stay with full throttle position,
then to "OFF" position, then gradually advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
    such as lots of built-in security features. One such function COULD
    POTENTIALLY CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an extremely low position and/or if
    rotation of the brushless motor is restrained or blocked in some
    way. This is NORMAL, as the ESC is discovering that an issue
    potentially exists with the motor and/or speed control. Rotation of
    the motor is stopped to secure the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually already been armed and the motor has been
rotating generally, yet after moving the throttle stay with near minimum the
motor all of a sudden ceases to rotate generally even if the throttle stick is advanced
above minimum throttle, DO NOT LOCATION YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD RESULT IN INJURY!! From this point, moving
the throttle hold up - even to full throttle may not trigger the motor to
rotate BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To regain
control of the motor, move the throttle stay with absolute minimum throttle
position then advance the throttle stick up-wards as soon as again.
Alternatively, you can detach the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
get near the propeller if the speed control is connected to input power!
ALWAYS
make sure the throttle stick is at minimum position prior to trying to
detach the battery from the speed control! ElectriFly is not responsible
for incidental damage or injury as a result of misuse of this product.