Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small airplanes, gliders, electric helicopters and 1/18 scale automobiles

INCLUDES:
HS-82MG Metal Gear Micro Servo with universal port, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

REQUIRES:
Setting up in model and connecting to receiver

SPECIFICATIONS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are readily available;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want an additional wonderful thing to match the above discussed thing?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency planes. Delivering
45A of continuous current with a built-in Battery Circuit
which can manage 2A, this ESC is basic to utilize
and extremely affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz changing frequency, for great run time and cool operation
Pre-installed Universal radio port* (see Comments listed below)
Pre-installed WS Deans Ultra male port for battery (see
Comments listed below)
Pre-installed gold plated 4mm female bullet connectors for motor
High powered changing BEC (Battery Eliminator Circuit) which
    deals with 3 or 4 basic servos
Complete proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see details in Comments listed below)
Thermal Security stops motor when maximum temperature 230°F
    is reached
180 Day Warranty (USA & Canada Only)

INCLUDES:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver port, battery port, and motor
    connectors.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery port, use: WSDM3000

SPECIFICATIONS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Present: 45A continuous maximum
50A rise maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Running frequency: 16kHz repaired
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To utilize with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle adhere to full throttle position,
then to "OFF" position, then gradually advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
    such as lots of integrated safety functions. One such function COULD
    POSSIBLY CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an exceptionally low position and/or if
    rotation of the brushless motor is impeded or blocked in some
    way. This is NORMAL, as the ESC is detecting that an issue
    potentially exists with the motor and/or speed control. Rotation of
    the motor is stopped to secure the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually already been equipped and the motor has been
rotating typically, yet after moving the throttle adhere to near minimum the
motor unexpectedly ceases to turn typically even if the throttle stick is advanced
above minimum throttle, DO NOT RESTAURANT YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD RESULT IN ACCIDENT!! From this point, moving
the throttle hold up - even to full throttle may not cause the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To restore
control of the motor, move the throttle adhere to outright minimum throttle
position then advance the throttle stick up-wards once again.
Alternatively, you can detach the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
come up to the propeller if the speed control is linked to input power!
ALWAYS
make certain the throttle stick is at minimum position prior to trying to
detach the battery from the speed control! ElectriFly is not responsible
for incidental damage or accident as an outcome of abuse of this product.