Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small aircrafts, gliders, electrical helicopters and 1/18 scale cars

SUCHES AS:
HS-82MG Metal Gear Micro Servo with universal adapter, 0.67" (17mm)
    diameter horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

REQUIRES:
Installing in design and linking to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are offered;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want one more great item to enhance the above mentioned item?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for larger high efficiency airplanes. Providing
45A of continuous existing with a built-in Battery Circuit
which can manage 2A, this ESC is basic to utilize
and really affordable.

FEATURES:
Compatible with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz changing frequency, for great run time and cool operation
Pre-installed Universal radio adapter* (see Remarks listed below)
Pre-installed WS Deans Ultra male adapter for battery (see
Remarks listed below)
Pre-installed gold plated 4mm female bullet adapters for motor
High powered changing BEC (Battery Remover Circuit) which
    handles 3 or 4 standard servos
Full proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see information in Remarks listed below)
Thermal Defense stops motor when maximum temperature level 230°F
    is reached
180 Day Guarantee (U.S.A & Canada Just)

SUCHES AS:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver adapter, battery adapter, and motor
    adapters.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery adapter, use: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Current: 45A continuous maximum
50A rise maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz fixed
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To utilize with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle stay with full throttle position,
then to "OFF" position, then gradually advance throttle and motor will
start to run.

The "Silver Series" line of brushless electronic speed controls
    include many built-in security features. One such feature COULD
    POSSIBLY CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an extremely low position and/or if
    rotation of the brushless motor is hampered or blocked in some
    way. This is NORMAL, as the ESC is discovering that an issue
    possibly exists with the motor and/or speed control. Rotation of
    the motor is stopped to safeguard the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually already been armed and the motor has been
turning generally, yet after moving the throttle stay with near minimum the
motor unexpectedly ceases to turn generally even if the throttle stick is advanced
above minimum throttle, DO NOT RESTAURANT YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS CAUTION COULD LEAD TO ACCIDENT!! From this point, moving
the throttle stick up - even to full throttle may not trigger the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To restore
control of the motor, move the throttle stay with outright minimum throttle
position and then advance the throttle stick up-wards when again.
Alternatively, you can disconnect the battery from the ESC, then re-connect the
source of power and re-arm the system.
NEVER
come up to the propeller if the speed control is linked to input power!
ALWAYS
ensure the throttle stick is at minimum position before attempting to
disconnect the battery from the speed control! ElectriFly is not accountable
for incidental damage or accident as an outcome of abuse of this product.