Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Equipment Micro Servo from Hitec.

FEATURES:
For little planes, gliders, electric helicopters and 1/18 scale automobiles

SUCHES AS:
HS-82MG Metal Equipment Micro Servo with universal adapter, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

REQUIRES:
Installing in design and linking to receiver

SPECIFICATIONS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are offered;
Equipment Set, HRCM6386
Horn Set, HRCM6326

Want an additional excellent product to compliment the above stated product?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high performance airplanes. Delivering
45A of continuous present with an integrated Battery Circuit
which can handle 2A, this ESC is easy to utilize
and extremely affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for excellent run time and cool operation
Pre-installed Universal radio adapter* (see Comments listed below)
Pre-installed WS Deans Ultra male adapter for battery (see
Comments listed below)
Pre-installed gold plated 4mm female bullet ports for motor
High powered switching BEC (Battery Eliminator Circuit) which
    manages 3 or 4 conventional servos
Full proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see information in Comments listed below)
Thermal Protection stops motor when maximum temperature 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Only)

SUCHES AS:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver adapter, battery adapter, and motor
    ports.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery adapter, use: WSDM3000

SPECIFICATIONS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Current: 45A continuous maximum
50A surge maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz repaired
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To utilize with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle adhere to full throttle position,
then to "OFF" position, then gradually advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
    include many integrated security functions. One such function COULD
    POSSIBLY TRIGGER THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an incredibly low position and/or if
    rotation of the brushless motor is hindered or blocked in some
    way. This is NORMAL, as the ESC is finding that a problem
    perhaps exists with the motor and/or speed control. Rotation of
    the motor is stopped to safeguard the speed control from possible
    damage.
WARNING!!
If the ESC and motor have already been armed and the motor has been
rotating typically, yet after moving the throttle adhere to near minimum the
motor unexpectedly ceases to turn typically even if the throttle stick is advanced
above minimum throttle, DO NOT RESTAURANT YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD RESULT IN PERSONAL INJURY!! From this point, moving
the throttle stick up - even to full throttle might not trigger the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To regain
control of the motor, move the throttle adhere to absolute minimum throttle
position then advance the throttle stick upwards when again.
Alternatively, you can detach the battery from the ESC, then re-connect the
source of power and re-arm the system.
NEVER
get near the propeller if the speed control is connected to input power!
ALWAYS
make certain the throttle stick is at minimum position before attempting to
detach the battery from the speed control! ElectriFly is not accountable
for incidental damage or injury as an outcome of abuse of this item.