Great Planes Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for use on 28mm Motors.

FEATURES:
Aluminum building and construction

CONSISTS OF:
One Prop Saver
Two Rubber O-Rings
Two Bushings

NEEDS:
Setup on Rimfire 28mm Motor

Right here is a excellent item that numerous others have purchased the very same time.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specifications:
Dimension : 23mm x 12mm x 29mm
Connector Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing material:
1 x 9g TITAN Servo Sets (with accessories)

This item compliments the above discussed item.

930Kv Brushless Outrunner Motor, 3.17 MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1800Kv
Max. effectiveness current: 6-10 Amp
NoLoad current / 10 V: 0.8 Amp
Current capability: 16 A/60 s
Max. Effectiveness: 74%
Shaft size: 3mm

A2208-12 much like: AXI 2208/20, E-Flite Park 370

This item compliments the main item here.

6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Precision Composites.
For utilize on Electric powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 2 adjuster rings that adapt to various motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
Two composite adapter rings
One direction sheet

NEEDS:
Assembly onto motor or gear drive system in your Electric plane.
Balancing

SPECS:
Size: 6"
Pitch: 4
Hub inner size: 0.25"

REMARKS:
Use Speed 400 Electric motors.

Right here is a excellent item that numerous others have purchased the very same time.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building and construction decreases turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist keep real, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring direction sheet

NEEDS:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Radiance engines

Right here is one more item that compliments the item being discussed.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Precision Composites.
For utilize on electrical powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite building and construction
Has 2 adjuster rings that adapt to various motor shafts

CONSISTS OF:
One 7x6EP Thin Electric Propeller

NEEDS:
ALL props require balancing, this is EXTREMELY vital, utilize TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Size: 7"
Pitch: 6
Hub inner size: 0.25" (6.3mm)