Gmade Xd Piggyback Shock 103Mm (2Pcs)

This is the Gmade 103mm XD Piggyback Shock Set.

 

Functions:

Fits 1/8 & 1/10 scale crawlers & trucks, 1/10 scale EP buggys and Short course trucks (such as Gmade R1, Axial Wraith and XR-10, Traxxas E-Maxx and 2WD Slash rear)
Easy shock setup changes utilizing adjustable piggyback valve
CNC machined aluminum shock bodies, aeration screws and piggyback bodies
Titanium gray anodized shock bodies
Red anodized aeration screws
Silver anodized piggyback bodies
Lower shock ends includes red anodized aluminum balls
Completely threaded for rapid modification
Delrin pistons
3.5mm thick shock shafts
Shaft exits through double O-ring seals
Easy load shock seal assembly
Laser etched for authenticity
Requirements:

Length (Mounting hole to hole): 103mm

Shock Body Diameter: 14mm

Spring Diameter: 19mm

Spring Length: 68mm

Full Shaft Travel Variety: 31mm (without Rubber bump stop)

Shaft Diameter: 3.5mm

Consists of:

(2) Titanium gray anodized aluminum shock bodies
(2) Red anodized aluminum aeration screws
(2) Silver anodized aluminum piggyback bodies
(2) Shock springs
All needed hardware to complete the shocks
Assembly instructions
Bottle of shock oil

Want one more fantastic item to enhance the above pointed out item?

Xd Piggyback Shock 85Mm (2Pcs)

This is the Gmade 85mm XD Piggyback Shock Set. 

 

Functions:

Fits 1/10 scale crawlers & trucks, 1/10 scale Short course trucks (such as Tamiya F350 High-lift, Traxxas 2WD Slash front)
Easy shock setup changes utilizing adjustable piggyback valve
CNC machined aluminum shock bodies, aeration screws and piggyback bodies
Titanium gray anodized shock bodies
Red anodized aeration screws
Silver anodized piggyback bodies
Lower shock ends includes red anodized aluminum balls
Completely threaded for rapid modification
Delrin pistons
3.5mm thick shock shafts
Shaft exits through double O-ring seals
Easy load shock seal assembly
Laser etched for authenticity
Requirements:

Length (Mounting hole to hole): 85mm

Shock Body Diameter: 14mm

Spring Diameter: 19mm

Spring Length: 50mm

Full Shaft Travel Variety: 22mm (without Rubber bump stop)

Shaft Diameter: 3.5mm

Consists of:

(2) Titanium gray anodized aluminum shock bodies
(2) Red anodized aluminum aeration screws
(2) Silver anodized aluminum piggyback bodies
(2) Shock springs
All needed hardware to complete the shocks
Assembly instructions
Bottle of shock oil

Below is one more item that praises the item being gone over.

Waterproof Standard Digital Servo 0.15Sec / 208Oz @ 6V

The SW0231MG is a budget friendly water resistant digital servo with terrific torque for numerous applications. This brushed servo features a speed of .17 and 208.0 oz-in of torque 6.0V. It integrates leading edge technology with super high 12-bit (4096) resolution and metal equipments for your higher accuracy when dodging puddles. This is a terrific upgrade if your looking to drive your RC automobile in any condition...rain, sleet, or snow.

Functions:

• Combines cutting edge
  technology with super high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Incredibly strong metal equipments make sure long-life and durability.
• Our servos are absolutely green ? from products to production, these servos are environmentally friendly.
• Ideal for RC vehicles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Gear: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Rating: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520