Gmade Xd Piggyback Shock 103Mm (2Pcs)

This is the Gmade 103mm XD Piggyback Shock Set.

 

Functions:

Fits 1/8 & 1/10 scale crawlers & trucks, 1/10 scale EP buggys and Short course trucks (such as Gmade R1, Axial Wraith and XR-10, Traxxas E-Maxx and 2WD Slash rear)
Easy shock setup modifications using adjustable piggyback valve
CNC machined aluminum shock bodies, aeration screws and piggyback bodies
Titanium gray anodized shock bodies
Red anodized aeration screws
Silver anodized piggyback bodies
Lower shock ends suches as red anodized aluminum balls
Fully threaded for rapid change
Delrin pistons
3.5mm thick shock shafts
Shaft exits through double O-ring seals
Easy load shock seal assembly
Laser inscribed for credibility
Requirements:

Length (Installing hole to hole): 103mm

Shock Body Size: 14mm

Spring Size: 19mm

Spring Length: 68mm

Full Shaft Travel Variety: 31mm (without Rubber bump stop)

Shaft Size: 3.5mm

Suches as:

(2) Titanium gray anodized aluminum shock bodies
(2) Red anodized aluminum aeration screws
(2) Silver anodized aluminum piggyback bodies
(2) Shock springs
All needed hardware to finish the shocks
Assembly directions
Bottle of shock oil

Want an additional great item to compliment the above mentioned item?

Xd Piggyback Shock 85Mm (2Pcs)

This is the Gmade 85mm XD Piggyback Shock Set. 

 

Functions:

Fits 1/10 scale crawlers & trucks, 1/10 scale Short course trucks (such as Tamiya F350 High-lift, Traxxas 2WD Slash front)
Easy shock setup modifications using adjustable piggyback valve
CNC machined aluminum shock bodies, aeration screws and piggyback bodies
Titanium gray anodized shock bodies
Red anodized aeration screws
Silver anodized piggyback bodies
Lower shock ends suches as red anodized aluminum balls
Fully threaded for rapid change
Delrin pistons
3.5mm thick shock shafts
Shaft exits through double O-ring seals
Easy load shock seal assembly
Laser inscribed for credibility
Requirements:

Length (Installing hole to hole): 85mm

Shock Body Size: 14mm

Spring Size: 19mm

Spring Length: 50mm

Full Shaft Travel Variety: 22mm (without Rubber bump stop)

Shaft Size: 3.5mm

Suches as:

(2) Titanium gray anodized aluminum shock bodies
(2) Red anodized aluminum aeration screws
(2) Silver anodized aluminum piggyback bodies
(2) Shock springs
All needed hardware to finish the shocks
Assembly directions
Bottle of shock oil

Right here is an additional item that praises the item being discussed.

Waterproof Standard Digital Servo 0.15Sec / 208Oz @ 6V

The SW0231MG is a budget plan friendly water resistant digital servo with excellent torque for many applications. This brushed servo features a speed of .17 and 208.0 oz-in of torque 6.0V. It integrates leading edge technology with incredibly high 12-bit (4096) resolution and metal gears for your higher accuracy when dodging puddles. This is a terrific upgrade if your wanting to drive your RC vehicle in any condition...rain, sleet, or snow.

Functions:

• Integrates leading edge
  technology with incredibly high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Incredibly strong metal gears guarantee long-life and durability.
• Our servos are totally green ? from products to production, these servos are ecologically friendly.
• Ideal for RC cars, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Equipment: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Score: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520