E-Flite Power 10 Brushless Outrunner Motor, 1100Kv

Functions



Equivalent to a 10-size glow engine for 32–48 ounce (910–1360 g) aircraftsIdeal for 3D airplanes weighing 28–36 ounces (790–1020 g)Ideal for designs requiring approximately 450 watts of powerHigh-torque, direct-drive alternative to inrunner brushless motorsIncludes install, prop adapters and mounting hardwareExternal rotor design—5mm shaft can quickly be reversed for alternative motor installationsSlotted 14-pole outrunner designHigh-quality building with ball bearings and hardened steel shaftQuiet, light-weight operation




Overview


The Power 10 is designed to provide tidy and peaceful power for 10-size sport and scale aircrafts weighing 32 to 48 ounces (910 to 1360 grams), 3D aircrafts weighing 28 to 36 ounces (790 to 1020 grams), or designs requiring approximately 450 watts of power. It’s a particularly excellent match for the E-flite Brio 10 for high speed F3A precision or creative aerobatics.







Tech Notes


* Maximum Operating Temperature level: 220 degrees Fahrenheit
* Adequate cooling is needed for all motor operation at optimal present levels.
* Maximum Burst Current duration is 15 seconds. Adequate time between maximum burst intervals is needed for proper cooling and to prevent overheating the motor.
* Maximum Burst Current rating is for 3D and limited motor run flights. Lack of proper throttle management may result in damage to the motor because extreme use of burst current may overheat the motor.

Examples of Plane Setups:
Please see our website for the most current information and aircraft setup examples.

NOTE: All data measured at full throttle. Real efficiency may vary depending upon battery and flight conditions.
E-flite Brio 10

Motor: Power 10
ESC: E-flite 40A Brushless V2 (EFLA311B)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power PRO LITE 2100mAh 11.1V 3-Cell (THP21003SPL)
Flying Weight w/Battery: 2.1 pounds

Amps   Volts   Watts      Input Watts/Pound     RPM
37.2      9.6       357               170                 7800

Expect excellent speed and extreme vertical power for creative aerobatics. Average duration is approximately 6-9 minutes depending upon throttle management.

E-flite Ultimate 20-300 10e

Motor: Power 10
ESC: E-flite 40A Lite Pro SB Brushless (EFLA1040L)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power 2600mAh 11.1V THREE PRO LITE V2 Li-Po (THP26003SPL2)
Flying Weight w/Battery: 40.7 oz (2.5)

Amps     Volts     Watts       Input Watts/Pound      RPM
40.2        10.7      430                    172               8350

Expect ballistic power extremely strong vertical efficiency perfect for pulling out of hovers. Average duration is approximately 5-8 minutes depending upon throttle management.


You will need...
40A ESC
6- to 10-cell Ni-MH/Ni-Cd or 2–THREE Li-Po
10x5 to 12x6 electrical props






Specs


Type: Brushless outrunner motor
Size: 10-size
Bearings or Bushings: One 5 x 14 x 5mm Bearing, and One 5 x 11 x 5mm Bearing
Wire Gauge: 16
Recommended Prop Variety: 10x5–12x6
Voltage: 7.2–12
RPM/Volt (Kv): 1100
Resistance (Ri): .043 ohms
Idle Current (Io): 2.10A @10V
Constant Current: 32A
Maximum Burst Current: 42A (15 sec)
Cells: 6–10 Ni-MH/Ni-Cd or 2–THREE Li-Po
Speed Control: 35–40A brushless
Weight: 122 g (4.3 oz)
General Diameter: 35mm (1.40 in)
Shaft Diameter: 5mm (.20 in)
General Length: 43mm (1.60 in)






Articles, Reviews, and Hyperlinks




 Preview: E-flite RV-9 450 ARF


 John Redman Assists Us Put together The E-flite DHC-2 Beaver 25e


 Preview – E-flite Nieuport 17 250 ARF


 John Redman reveals us the new E-flite PT-19