E-Flite Power 10 Brushless Outrunner Motor, 1100Kv

Features



Comparable to a 10-size glow engine for 32–48 ounce (910–1360 g) planesPerfect for 3D airplanes weighing 28–36 ounces (790–1020 g)Ideal for designs requiring as much as 450 watts of powerHigh-torque, direct-drive option to inrunner brushless motorsIncludes mount, prop adapters and installing hardwareExternal rotor design—5mm shaft can easily be reversed for alternative motor installationsSlotted 14-pole outrunner designHigh-quality building and construction with ball bearings and hardened steel shaftQuiet, lightweight operation




Introduction


The Power 10 is developed to provide clean and peaceful power for 10-size sport and scale planes weighing 32 to 48 ounces (910 to 1360 grams), 3D planes weighing 28 to 36 ounces (790 to 1020 grams), or designs requiring as much as 450 watts of power. It’s an especially good match for the E-flite Brio 10 for high speed F3A accuracy or creative aerobatics.







Tech Notes


* Maximum Operating Temperature level: 220 degrees Fahrenheit
* Adequate cooling is needed for all motor operation at optimal existing levels.
* Maximum Burst Current period is 15 seconds. Sufficient time between maximum burst intervals is needed for appropriate cooling and to prevent overheating the motor.
* Maximum Burst Current rating is for 3D and limited motor run flights. Lack of appropriate throttle management might lead to damage to the motor since excessive use of burst current might get too hot the motor.

Examples of Plane Setups:
Please see our website for the most up-to-date information and aircraft setup examples.

NOTE: All data determined at complete throttle. Real performance might differ depending on battery and flight conditions.
E-flite Brio 10

Motor: Power 10
ESC: E-flite 40A Brushless V2 (EFLA311B)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power PRO LITE 2100mAh 11.1V 3-Cell (THP21003SPL)
Flying Weight w/Battery: 2.1 pounds

Amps   Volts   Watts      Input Watts/Pound     RPM
37.2      9.6       357               170                 7800

Anticipate good speed and extreme vertical power for creative aerobatics. Typical period is approximately 6-9 minutes depending on throttle management.

E-flite Ultimate 20-300 10e

Motor: Power 10
ESC: E-flite 40A Lite Pro SB Brushless (EFLA1040L)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power 2600mAh 11.1V 3S PRO LITE V2 Li-Po (THP26003SPL2)
Flying Weight w/Battery: 40.7 oz (2.5)

Amps     Volts     Watts       Input Watts/Pound      RPM
40.2        10.7      430                    172               8350

Anticipate ballistic power very strong vertical performance ideal for taking out of hovers. Typical period is approximately 5-8 minutes depending on throttle management.


You will need...
40A ESC
6- to 10-cell Ni-MH/Ni-Cd or 2–3S Li-Po
10x5 to 12x6 electric props






Specifications


Type: Brushless outrunner motor
Size: 10-size
Bearings or Bushings: One 5 x 14 x 5mm Bearing, and One 5 x 11 x 5mm Bearing
Wire Gauge: 16
Suggested Prop Range: 10x5–12x6
Voltage: 7.2–12
RPM/Volt (Kv): 1100
Resistance (Ri): .043 ohms
Idle Current (Io): 2.10A @10V
Continuous Current: 32A
Maximum Burst Current: 42A (15 sec)
Cells: 6–10 Ni-MH/Ni-Cd or 2–3S Li-Po
Speed Control: 35–40A brushless
Weight: 122 g (4.3 oz)
General Diameter: 35mm (1.40 in)
Shaft Diameter: 5mm (.20 in)
General Length: 43mm (1.60 in)






Articles, Reviews, and Links




 Sneak peek: E-flite RV-9 450 ARF


 John Redman Assists Us Put together The E-flite DHC-2 Beaver 25e


 Sneak peek – E-flite Nieuport 17 250 ARF


 John Redman shows us the new E-flite PT-19