Dubro Mini E/Z Connector 2/Pkg

These are Mini E-Z Connectors for Park Flyers by Dubro.

FEATURES:
Aluminum Building

CONSISTS OF:
2 Connectors
2 Screws
2 Washers

REQUIRES:
Absolutely nothing

SPECIFICATIONS:
Length: 4.8mm (3/16")
Diameter: 3.2mm (1/8")
Weight: 0.25g (0.0088oz)

REMARKS:
Optimum pushrod size is .047 - 3/64" (1.22mm)

Lots of others have actually purchased this item in addition to the item that you are presently reading about.

Control Horn Nylon 1/2A (2)

These are 1/2A T-Style Control Horns.

FEATURES:
Nylon building

CONSISTS OF:
2 control horns w/4 adjusting holes and 2 installing holes
(3/4" long [tall])
2 installing plates w/2 installing holes (3/8"x3/8")
4 2-56x3/8" round head screws

REQUIRES:
A flat head (slotted) screwdriver

SPECIFICATIONS:
See "consists of" above

This item praises the main item below.

Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and lightweight for installing in little planes,
    electrics or gliders, where really high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train supplies dependable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One really little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

Below is a fantastic item that many others have actually purchased the exact same time.

E-Z Connector For Rod Or Cable

This is an EZ Port set by Dubro.
EZ Connectors link a pushrod to a servo arm enabling it to pivot for
less going in control surfaces.

FEATURES:
Functions on 2-56 and smaller wire (.078")
Permanent or snap on installing push nuts both included.

INCLUDES:
2 brass EZ Connectors
2 plastic snap nuts.
Two metal snap nuts.
Two 2.5x3.5mm slotted head screws.

REQUIRES:
Assembly onto linkages

SPECIFICATIONS:
Length of brass port: 10mm (.395")
Diameter of brass port: 5.5mm (.217")

Lots of others have actually purchased this item in addition to the item that you are presently reading about.

9x4.7 Slow Flyer Propeller

This is a 9x4.7 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Composite building
Strengthening carbon fibers help maintain true, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

REQUIRES:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 9"
Pitch: 4.7

REMARKS:
Slo-Flyer props are Not designed for Glow engines

Below is an additional item that praises the item being gone over.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specifications:
Measurement : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing content:
1 x 9g TITAN Servo Sets (with accessories)