Castle Creations Sidewinder 3 Waterproof 1:10Th 12V Sport Car Esc

This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control.

FEATURES:
Suggested for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) ready to run (not for use in much heavier
    cars such as E-Revos or E-Maxx class cars)
USB shows capability by means of Castle Link USB adapter (not included,
    order CSEM6300)
Water resistant for use in almost every environment (not meant for
    operation while submerged in liquid)
Suitable with the Castle Creations 14xx series NeuCastle motors
Reversible with reverse lockout

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Connector
    On/Off Switch, and Instructions

REQUIRES:
Battery ports

SPECS:
Input Voltage: TWO LiPo minimum, THREE LiPo maximum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery adapter

Right here is a fantastic thing that lots of others have actually bought at the same time.

Push Rod Assmbld W/Rod Ends (2) For Use W/#5359 Revo

These are the (optional) Steel Pushrods for the Rocker Arms
for the REVO from Traxxas
These go in between the Rocker Arms and the Lower Suspension Arms

FEATURES:
Black steel construction

CONSISTS OF:
Two Pushrods w/pre-installed rod ends and balls

REQUIRES:
Setting up on the automobile

SPECS:
Length: 5.4" (137mm) end to end consisting of rod ends
Diameter: 0.20" (5mm)

COMMENTS:
For rod ends just utilize TRAC5347

This thing compliments the above gone over thing.

Castle Bec 10Amp (25 Volt Max Input)

This is the CC BEC 10A Receiver Battery Remover by Castle Creations.

FEATURES:
Removes the requirement for a receiver and servo battery pack
Draws higher voltage from the motor batteries and drops it to a
    voltage level suitable for the receiver and servos

CONSISTS OF:
One CC BEC receiver battery remover

REQUIRES:
Installation in the aircraft

SPECS:
Length: 1.2" (30mm)
Width: .6" (15mm)
Height: .4" (10mm)
Weight: .4oz (11g)
Input voltage: 5V to 25.2V (TWO to 6S LiPo)
Current output: 12 volts input = 7 amps* continuous, 10 amp peak;
    24 volts input = 5 amps* continuous, 7 amp peak
    *Ratings are identified with a 5mph air flow on the BEC
Selectable Output: 4.8 - 9.0V by means of the Castle Link (offered separately)
    Default voltage is 5.1V

This thing compliments the above gone over thing.

Rock Crawler Brushed Motor 35T HD

This is the Tekin T35 HD 35 Turn Rock Crawler Brushed Motor.

FEATURES:
High-strength updated ferrite magnets
Legal for rock crawling competitions
Totally rebuildable
Double precision ball bearings
120 day minimal warranty

CONSISTS OF:
Tekin T35 HD 35 Turn Rock Crawler Brushed Motor

REQUIRES:
ESC such as the Tekin FXR Brushed ESC, TEKM1091
Motor leads
Pinion gear depending upon automobile

SPECS:
Input Voltage: THREE LiPo or 10-cell NiMH battery
Measurements: 2.07 x 1.42" (52.7 x 36mm)
Shaft Diameter: 0.125" (3.2mm)
Bearing Size: 3/8 x 1/8"
Motor Weight: 5.98oz (169g)