Castle Creations Monster 2 1:8Th 25V Car Esc Waterproof W/ 2200Kv Motor *Replaces

This Castle Mamba Monster 2 Water resistant 1/8 Scale Brushless Combo includes the sensored 1515 2200Kv motor and is suggested for large 1/8 scale trucks and buggies weighing less than 15 pounds ready-to-run with batteries.

The Mamba Monster 2 is an exceptionally powerful sensorless ESC capable of 2S to 6S LiPo operation. It's likewise water resistant*, so you can run your automobile throughout the early morning dew, through soaked snow, or practically anywhere else you?d be intrigued in running a 1:8 scale RC buggy or truck. It features an easy-access case permitting you to replace fans rapidly, if necessary. Furthermore, Mamba Monster 2 functions solder posts, so changing battery wire length and instructions is basic for an even more customized install.

Castle Creations 1515 1Y Sensored 4-Pole Brushless Motors combine rotor position sensor innovation with an enhanced high power and high effectiveness motor design to deliver ultra smooth startup, precise low speed control, predictable power shipment, amazing torque, and lightning quick response. Through making use of Castle's Smart Sense innovation, the position of the rotor is always known by the ESC. This removes the possibility of experiencing cogging or inconsistency during startup, and permits the 1512 to deliver ACCURATE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for.



NOTE:

Not planned for operation while submerged in liquid. If unit is run in wet conditions, rinse with fresh water to remove dirt or corrosives, then fully dry unit.
The cooling fan must be removed prior to driving in wet conditions. It is not waterproof.

Motor Features:

4-POLE 12-SLOT design boasts exceptional EFFECTIVENESS and produces LESS HEAT
Large gold plated solder tabs for LESS RESISTANCE and easy soldering
QUIETSENSE? Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at perpetuities
HIGHER PRECISION and MORE EFFECTIVE start-ups
OPTIMIZED design removes the requirement for mechanical timing modifications
Sensor alignment approach provides consistent timing and torque in both directions, immediately
REBUILDABLE design permits users to replace front end bell with bearings or rotors with shaft
ROAR basic sensor port and labeled connections
High strength 180?C neodymium sintered magnets
High quality, temperature-stabilized sensing units
High-purity, high-temperature copper windings
Solidified stainless-steel shaft
10 AWG high strand wire with silicone insulation
Kevlar wrapped rotor
6061-T6 Billet aluminum heatsink can
High RPM NMB oversized bearings
High quality 0.2mm steel laminations
Low resistance gold plated bullet ports

Specifications:

ESC

Input Voltage Range: 2S - 6S LiPo
BEC Specifications: User selectable output in between 5 and 7 volts; default 5.5 volts
Operating Environment: Water resistant* design permits use in almost any environment
Brake: Proportional
Reversible: Yes, but might be disabled for racing
On/Off Switch: Yes
Cooling Fan: Yes, factory equipped, fully detachable** (see Item Use Statements below)
Length: 2.19" (56mm)
Width: 1.86" (47mm)
Height: 1.33" (34mm)
Weight (without any battery port): 3.93 oz. (111.5 g)
Connectors: 6.5mm female bullets for motor connection. No battery port
Application Standards: Planned for up to 6S (25.2 Volt) operation in cars weighing less than 15 pounds, with batteries, ready-to-run.
Recommended Motors: Neu-Castle 1512 2650Kv: Max Cells: FOUR Lipo or 12 NiMH
Neu-Castle 1515 2200Kv: Max Cells: 6S Lipo or 16 NiMH
Max. Advised Car Weight: Less than 15 pounds, with batteries, ready-to-run with 2200kv motor; say goodbye to than 9 pounds with 2650kv motor.
Programmability: Fully programmable Castle feature set utilizing Castle Link USB adapter (discount coupon free of charge Link included) and freely downloadable Castle Link Windows software.
Telemetry Link Capable: No

Motor

Input Voltage Range: 2-6S LiPo
Kv: 2200
Max. RPM: 60,000
Length: 75.4mm
Diameter: 40mm (41.1mm w/fins)
Weight (w/wires): 429 g / 15.1oz
Shaft Size: 20mm
Diameter: 5mm
Installing Hole Specifications: M3 & M4 @ 25mm
Connectors: 6.5mm male Castle Bullet Connectors
Application Standards: Ideal for 1:8 scale off-road and on-road cars as well as 1:10 scale Monster Trucks up to 15lbs.
Max. Advised Car Weight: Up to 15lbs
Running modes: SMARTSENSE?, Sensored, Sensorless

NOTE: Not all LiPos are produced equal, and surge ratings must never be utilized to identify a pack?s viability for a brushless application. Use the CONSTANT C ranking only. Mamba Monster setups frequently strike 100+ amps in peaks. Castle strongly suggest utilizing 5,000 mAh or larger LiPo cells with a discharge ranking of a minimum of 30C (or high quality 25C batteries such as Traxxas? Power Cells?). Use only mild equipment ratios with NiMH cells. Do not attempt to utilize NiMH cells in severe setups.