Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors size in between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature as much as 30°
One year limited service warranty through maker start at date of
    purchase

SUCHES AS:
Fan with wire and adapter, shroud and two zip ties

REQUIRES:
Attaching to motor can and plugging into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want an additional wonderful product to compliment the above discussed product?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

SUCHES AS:
Fan with Wire Lead and Port
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, get rid of prior to exposing ESC to moisture

The below product also sets truly well with the product being reviewed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Recommended for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) prepared to run (not for usage in heavier
    vehicles such as E-Revos or E-Maxx class vehicles)
USB shows ability by means of Castle Link USB adapter (not consisted of,
    order CSEM6300)
Water resistant for usage in almost every environment (not intended for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces lots of stock brushed motors
4 magnet, 4 pole rotor for greater torque
1.4" size slotted stator
Easily removable end bell

SUCHES AS:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Change, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery adapter of modeler's option

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, 3S LiPo maximum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery adapter
    Motor;
kV Score: 4600
Can Length: 1.9" (49mm)
Can Diameter: 1.4" (36mm)
Shaft Diameter: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)

Numerous others have actually bought this product along with the product that you are currently checking out.

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Below is an additional product that compliments the product being reviewed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

SUCHES AS:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is only one of two which are utilized on the E-Maxx double motor
    set-up.