Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outside size between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Connecteds into receiver and drops motor temperature as much as 30°
One year minimal warranty through manufacturer beginning at date of
    purchase

CONSISTS OF:
Fan with wire and adapter, shroud and two zip ties

REQUIRES:
Attaching to motor can and plugging into receiver

SPECS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want another excellent thing to compliment the above mentioned thing?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

CONSISTS OF:
Fan with Wire Lead and Adapter
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, remove before exposing ESC to moisture

The listed below thing also pairs really well with the thing being reviewed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Recommended for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) prepared to run (not for use in much heavier
    vehicles such as E-Revos or E-Maxx class vehicles)
USB programming ability by means of Castle Link USB adapter (not included,
    order CSEM6300)
Waterproof for use in almost every environment (not meant for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces numerous stock brushed motors
4 magnet, 4 pole rotor for higher torque
1.4" size slotted stator
Easily removable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Adapter,
    On/Off Switch, Instructions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery adapter of modeler's choice

SPECS:
ESC;
Input Voltage: 2S LiPo minimum, THREE LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery adapter
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Adapter: 4mm gold
Wire Length: 9.5" (241mm)

Lots of others have actually bought this thing together with the thing that you are currently reviewing.

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Below is another thing that praises the thing being reviewed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the gear which is connected directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is only one of two which are utilized on the E-Maxx dual motor
    set-up.