Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors size in between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature as much as 30°
One year restricted guarantee through producer beginning at date of
    purchase

SUCHES AS:
Fan with wire and connector, shroud and 2 zip ties

REQUIRES:
Connecting to motor can and plugging into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more fantastic product to match the above mentioned product?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older style cases used on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

SUCHES AS:
Fan with Wire Lead and Port
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove prior to exposing ESC to moisture

The listed below product also sets truly well with the product being talked about.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Suggested for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) prepared to run (not for usage in much heavier
    vehicles such as E-Revos or E-Maxx class vehicles)
USB shows ability by means of Castle Link USB adapter (not suched as,
    order CSEM6300)
Water resistant for usage in almost every environment (not planned for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes lots of stock brushed motors
4 magnet, four pole rotor for greater torque
1.4" size slotted stator
Detachable end bell

SUCHES AS:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Change, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery connector of modeler's option

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, 3S LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery connector
    Motor;
kV Score: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)

Numerous others have actually gotten this product in addition to the product that you are currently reviewing.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Below is one more product that compliments the product being talked about.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is connected directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

SUCHES AS:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is just one of 2 which are used on the E-Maxx dual motor
    set-up.