Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors size between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature level as much as 30°
One year restricted guarantee through manufacturer start at date of
    purchase

CONSISTS OF:
Fan with wire and connector, shroud and two zip ties

REQUIRES:
Connecting to motor can and connecteding into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more fantastic thing to match the above pointed out thing?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases used on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

CONSISTS OF:
Fan with Wire Lead and Adapter
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, get rid of prior to exposing ESC to moisture

The below thing likewise pairs really well with the thing being discussed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Recommended for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for use in much heavier
    cars such as E-Revos or E-Maxx class cars)
USB programming ability via Castle Link USB adapter (not suched as,
    order CSEM6300)
Waterproof for use in almost every environment (not intended for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes lots of stock brushed motors
Four magnet, four pole rotor for higher torque
1.4" size slotted stator
Removable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Adapter,
    On/Off Switch, Instructions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery connector of modeler's option

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, THREE LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery connector
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Diameter: 1.4" (36mm)
Shaft Diameter: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Adapter: 4mm gold
Wire Length: 9.5" (241mm)

Many others have gotten this thing along with the thing that you are presently reading about.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Here is one more thing that compliments the thing being discussed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is only one of two which are used on the E-Maxx double motor
    set-up.