Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outside diameter in between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Connecteds into receiver and drops motor temperature level as much as 30°
One year limited service warranty through producer start at date of
    purchase

SUCHES AS:
Fan with wire and port, shroud and two zip ties

NEEDS:
Attaching to motor can and plugging into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more wonderful product to compliment the above mentioned product?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older style cases used on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

SUCHES AS:
Fan with Wire Lead and Connector
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove prior to exposing ESC to moisture

The below product additionally pairs truly well with the product being reviewed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Recommended for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) prepared to run (not for usage in much heavier
    cars such as E-Revos or E-Maxx class cars)
USB programming ability via Castle Link USB adapter (not suched as,
    order CSEM6300)
Water resistant for usage in almost every environment (not planned for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes numerous stock brushed motors
Four magnet, 4 pole rotor for greater torque
1.4" diameter slotted stator
Detachable end bell

SUCHES AS:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Connector,
    On/Off Switch, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

NEEDS:
Battery port of modeler's choice

SPECIFICATIONS:
ESC;
Input Voltage: TWO LiPo minimum, THREE LiPo maximum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery port
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Connector: 4mm gold
Wire Length: 9.5" (241mm)

Lots of others have purchased this product along with the product that you are presently reviewing.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Here is one more product that praises the product being reviewed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

SUCHES AS:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is only one of two which are used on the E-Maxx dual motor
    set-up.