Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors diameter between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Connecteds into receiver and drops motor temperature level as much as 30°
One year minimal warranty through producer beginning at date of
    purchase

CONSISTS OF:
Fan with wire and port, shroud and two zip ties

REQUIRES:
Connecting to motor can and plugging into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more wonderful item to enhance the above discussed item?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older style cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

CONSISTS OF:
Fan with Wire Lead and Adapter
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, eliminate prior to exposing ESC to moisture

The listed below item additionally sets truly well with the item being talked about.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Advised for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for usage in much heavier
    cars such as E-Revos or E-Maxx class cars)
USB programming ability via Castle Link USB adapter (not included,
    order CSEM6300)
Water resistant for usage in almost every environment (not planned for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces many stock brushed motors
Four magnet, four pole rotor for higher torque
1.4" diameter slotted stator
Removable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Adapter,
    On/Off Switch, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery port of modeler's option

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, 3S LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery port
    Motor;
kV Score: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Adapter: 4mm gold
Wire Length: 9.5" (241mm)

Several others have actually bought this item together with the item that you are currently checking out.

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Right here is one more item that praises the item being talked about.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

CONSISTS OF:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of two which are utilized on the E-Maxx double motor
    set-up.