Axial SCX10 II Trail Honcho 1/10th Electric 4WD RTR

**Additional Technical Info Will Be Included When It Appears,**
This is the Electric Powered, Radio Controlled, 1/10 scale
Prepared to Run SCX10 II Trail Honcho 4WD.

FUNCTIONS:
Chassis: Scale steel C-channel side rails with adjustable body install,
    adjustable bumper mounts with swaybar installing points, installing
    points for optional 2-speed and servo winch, adjustable chassis
    mounted servo system
Drive: Full-time 4WD locked drivetrain with WB8 HD Wild Boar
    driveshafts, UVJ design front driveshafts for up to 45° of steering
    angle, complete ball bearing drivetrain
Transmission: AX10 three gear layout, metal motor plate, adjustable
    ratio for high speed or competition level crawling speed
Slipper Clutch: Double pad style for included area, 32P gear
    pitch for high-torque applications
Motor: 35 turn, brush equipped, water resistant, integrated cooling
    fan
Radio: Method TTX200 2-channel SLT radio with TR325 Receiver,
    steering and throttle end point adjustment & reverse, pushbutton
    steering and throttle trim
Guiding Servo: Method TSX45 metal gear, water resistant, 151oz/in
    (10.87kg/cm) torque ranking, dual ball bearings
ESC: AE-5L water resistant, switchable between LiPo or NiMH
    operation with a basic jumper, Star plug battery adapter,
    built-in LED light controller (KEEP IN MIND LED leads are not suitable
    with old Axial LED light strings, or third party LED light strings)
Spur Equipment: 56T 32-pitch, plastic construction
Pinion Equipment 15T 32-pitch, steel construction
LED Lights: Four white for head lights and turn signal markers, and
    two traffic signals for tail lights
Battery Tray: Easy access front install, accomodates batteries as much as
    5.75 x 1.2" (147 x 32mm) 3S, 5000mAh, with battery posts in
    position measurements are decreased to 5.4 x .94" (138 x 24mm)
Front and Rear Axles: Solidified steel
AR44 Hi-Pinion Axle: Hypoid cut CNC metal gears, enhanced gear
    ratio for decreased torque twist, optional tailoring options, one-
    piece axle housing, increased clearance, larger load rated
    bearings for toughness, 8° kingpin axle gets rid of tire scrub,
    single piece axle housing, one-piece all metal locker, 10°
    increment changes for knuckle carriers and straight axle
    adapters, enhanced gear ratio; 3.75 compared to 2.92 formerly,
    for less torque twist
Body: Painted Trail Honcho
Front Bumper: Scale tube style with aluminum skid plates
Wheels: 1.9" Technique Hole, 1.02" (26mm) broad, 2.12" (53.9mm) high,
    12mm hex, matte black surface
Tires: 1.9" Falken Wildpeak M/T, strongly treaded Mud Surface
    tread with incredible traction on lots of surface areas, 4.7" (119.4mm) high,
    1.5" (38.1mm) broad
Shocks: Coil over, oil filled, steel springs, white in color
Suspension: Enhanced suspension geometry with integrated mounts
    upper and lower links, 4-link style reduces axle steer
    and torque twist, and defend against suspension wrap-up in high-
    power applications, composite links
Steering: Correct CMS geometry using 3-link setup with panhard bar,
    45° steering angle
Warranty: One year bumper to bumper limited. Axial's service warranty center
    Pastime Providers will repair or replace any improperly made part.
    Proof of purchase is required for Axial to honor any service warranty
    claim. Axial reserves the right to change or customize this service warranty
    without notice. This service warranty does not cover damages due to typical
    wear and tear, users' failure to carry out routine upkeep, user
    error of assembly or installation, adjustments, abuse, crash
    damage, or the addition of aftermarket parts or optional parts.
    Note: Acquiring products from unapproved retailers may void the
    service warranty and prevent support and service.
    Repair or replacement of the product by Pastime Providers is the sole
    and special treatment for any loss or damages.

INCLUDES:
RTR SCX10 II Trail Honcho with Oil-Filled Shocks, Wheels, Tires,
    Body, Rock Sliders, Radio, ESC, Motor, Decals, Waterproof
    Receiver Box, LED Lights 4 AA Batteries and User's Manual

REQUIRES:
Battery: 6-cell NiMH or 2-3S LiPo
Battery Charger: Compatible with picked battery
Structure and track equipment

SPECIFICATIONS:
Car-
Length: 19.25" (489mm)
Width: 8.9" (226mm)
Height: 9.4" (223.4mm)
Stock Wheelbase: 12.3" (312.4mm), adjustable to 11.4" (289mm) or
    12.0" (305mm) with optional link sets sold separately
Ground Clearance: 3.0" (77mm)
Weight: 4.5pounds (2.04kg) around, with electronic devices
Enhanced Equipment Ratio: 3.75:1
Last Drive Ratio (FDR): 40.44, stock
    (33.69-54.15 with various spur/pinion gear mixes, extra
spur and pinion gears need to be bought separately)
    Body-
Length: 17.2" (438mm)
Width: 8" (203mm)
Height: 5.5" (140mm)

REMARKS:
For Replacement Ball Bearings use:
    Qty. Size Area Qty. Qty. Stock Number
2 7x14mm Ring Equipment 1 AXIC4406
2 5x14mm Pinion gear 1 AXIC4407
2 5x11mm Pinion Equipment 1 DTXC1547
2 10x15mm Front Uprights 1 DTXC1595
2 5x11mm Front Uprights 1 DTXC1547
2 5x11mm Rear Axles 1 DTXC1547
2 5x11mm 2-sp Top Shaft 1 DTXC1547
2 5x11mm 2-sp Bottom Shaft 1 DTXC1547
4 5x10mm Transfer Case 1 DTXC1535