Axial Diff Gasket 16x25x0.5mm

    This is a pair of replacement Differential Gaskets
for the Axial AX10 Scorpion Rock Crawler.

FEATURES:
Fiber building and construction, grey in color
Changes worn or damaged differential gaskets

CONSISTS OF:
Two Differential Gaskets

REQUIRES:
Setup following the design manual

SPECIFICATIONS:
Outdoors Size: 1" (25mm)
Inside Size: .67" (17mm)
Thickness: .020" (.52mm)

You will certainly enjoy this item if you have the item just above pointed out.



This is the Strong Bevel Gear Set for use on the
Axial AX10 Scorpion.

FEATURES:
Provides lower gear ratio and reduces torque twist
Steel building and construction

CONSISTS OF:
One 13T Bevel Gear
One 43T Bevel Gear

REQUIRES:
Setup on the automobile

The below product additionally sets actually well with the product being gone over.

Diff Case Small

This is the Small Differential Case for the Axial Rock Crawler.

FEATURES:
Plastic building and construction, black in color

CONSISTS OF:
Two small differential cases

REQUIRES:
Setup on the automobile

SPECIFICATIONS:
Size: .98" (25mm)
Height: .66" (17mm)

Lots of others have bought this product in addition to the product that you are currently reading about.

O-Ring 5x1mm (10)

These are the 5x1mm O-Rings from Axial.

FEATURES:
Rubber building and construction
Orange in color

CONSISTS OF:
Ten O-Rings

SPECIFICATIONS:
Outer Size: 6.5mm (0.25")
Inner Size: 5mm (0.196")
Thickness: 1mm (0.039")

Lots of others have bought this product in addition to the product that you are currently reading about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
External Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one needed).

This is a superb enhancement to the product currently being gone over.

O-Ring 2.5x1.5mm (10)

These are the 2.5x1.5mm O-Rings from Axial.

FEATURES:
Rubber building and construction
Orange in color

CONSISTS OF:
Ten O-Rings

SPECIFICATIONS:
Outer Size: 5.5mm (0.22")
Inner Size: 2.5mm (0.10")
Thickness: 1.5mm (0.06")

Right here is an additional product that praises the product being gone over.

Axle 5x35mm

This is a pair of replacement Axles
for the Axial AX10 Scorpion Rock Crawler.

FEATURES:
Steel building and construction, black in color
Changes worn or damaged axles
Works on the front or rear of the design

CONSISTS OF:
Two Axles

REQUIRES:
Setup following the design manual

SPECIFICATIONS:
Length: 1.37" (35mm)
Shaft Size: .20" (5mm) 4mm threaded

This is a superb enhancement to the product currently being gone over.

Aluminum Hub Narrow 12mm Black (4)

These are the 12mm Narrow Aluminum Hex Hubs from Axial.

FEATURES:
Aluminum building and construction, black in color
Changes worn or damaged hex centers

CONSISTS OF:
4 aluminum hex centers
4 steel drive pins
4 set screws

REQUIRES:
Setup following the design manual

SPECIFICATIONS:
Hex Size: .47" (12mm)

Right here is a fantastic product that several others have purchased the exact same time.



These are the Axial M3x61mm Hex Socket Button Head Screws.

FEATURES:
Steel building and construction. black in color

CONSISTS OF:
6 M3x61mm Hex Socket Button Head Screws

REQUIRES:
2mm hex wrench

SPECIFICATIONS:
Size: 3mm
Length: 61mm
Length of Threaded Area: 8mm

This product praises the above gone over product.

Hex Tap Button Head M3x10mm Black (10)

These are the Axial M3x10mm Hex Socket Tapping Button Head Screws.

FEATURES:
Black metal building and construction

CONSISTS OF:
Ten M3 x 10mm screws

REQUIRES:
Setup on automobile

COMMENTS:
Can be used wherever this size screw is needed