APC 8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building minimizes turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist preserve true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

NEEDS:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Glow engines

This is a great enhancement to the item presently being gone over.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon building minimizes turning mass for
    higher output and longer life
Developed for electrical powered Park Leaflet type aircraft with rear
    dealing with motors that "push" the aircraft forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with 2 finding rings and
    instruction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Density: 0.30" Hub diameter: 0.50"
Hole Diameter: 1/4"

NEEDS:
Only for use with electrical motors. Not for use with glow or gas
    engines.
All props require balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

This item is often bought with the above pointed out item.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is utilized in vehicles, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make sure they are capable
of delivering adequate amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon gears
One year guarantee

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

This item compliments the above gone over item.

Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and light-weight for mounting in little aircrafts,
    electrics or gliders, where extremely high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train supplies reputable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One extremely little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
Two M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)