APC 8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction minimizes turning mass for
    greater output and longer life.
Reinforcing carbon fibers assist keep true, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not designed for Radiance engines

This is a superb addition to the item currently being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Lightweight molded nylon building and construction minimizes turning mass for
    greater output and longer life
Designed for electrical powered Park Flyer type airplane with rear
    dealing with motors that "push" the airplane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with 2 finding rings and
    instruction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center diameter: 0.50"
Hole Diameter: 1/4"

REQUIRES:
Just for usage with electrical motors. Not for usage with radiance or gasoline
    engines.
All props need balancing, this is ESSENTIAL, utilize TOPQ5700.
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

This item is regularly purchased with the above stated item.



This is the Futaba S3003 Standard Servo.
This basic servo is utilized in automobiles, boats, or where conventional servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of delivering adequate amps.

INCLUDES:
One S3003 conventional servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangular rubber grommets (FUTM2348)
4 servo install screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon equipments
One year guarantee

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Connector: "J" type with approx. 5" lead

This item compliments the above talked about item.

Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and light-weight for mounting in little aircrafts,
    electrics or gliders, where really high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train provides reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One really little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)