APC 7x5 Thin Electric Prop

This is a 7x5E Thin Composite propeller from Advanced Accuracy Composites.
For use on Electric powered airplane just (not for radiance engines).

FEATURES:
Gray composite propeller blades that put together onto a propeller hub.
Comes with 2 adapter rings that adapt to different motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
Two composite adapter rings
One guideline sheet

REQUIRES:
ALL props require balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Diameter: 7"
Pitch: 5
Hub inner diameter: 0.25"

You will enjoy this thing if you have the thing previously pointed out.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Accuracy Composites.
For use on electric powered airplane just (not for radiance engines).

FEATURES:
Gray composite construction
Comes with 2 adapter rings that adapt to different motor shafts

INCLUDES:
One 7x6EP Thin Electric Propeller

REQUIRES:
ALL props require balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Diameter: 7"
Pitch: 6
Hub inner diameter: 0.25" (6.3mm)

Here is one more thing that compliments the thing being talked about.



This is a 6x5.5E Thin Composite Propeller from Advanced Accuracy Composites.
For use on Electric powered airplane just (not for radiance engines).

FEATURES:
Gray composite construction

INCLUDES:
One 6x5.5E Thin Electric Propeller

REQUIRES:
ALL props require balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Diameter: 6"
Pitch: 5.5
Hub inner diameter: 0.25"

The listed below thing likewise pairs really well with the thing being talked about.



These are the ElectriFly Prop Saver O-rings from Terrific Planes.

FEATURES:
Twists around the prop to hold it on and protect it throughout crashes

INCLUDES:
5 prop saver O-rings

REQUIRES:
Setup

Numerous others have acquired this thing in addition to the thing that you are currently reviewing.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Gear Type : All Nylon Gear
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specifications:
Dimension : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing content:
1 x 9g TITAN Servo Sets (with devices)

Want one more great thing to compliment the above mentioned thing?

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction reduces rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist preserve real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines