Align Skid Pipe

Apply to T-REX 550E.

Requirements:
Skid pipe x 2(Φ7.4xΦ9x294mm)
Skid pipe end cap x 4

This is a amazing enhancement to the item presently being talked about.

700F3C Landing Skid

Use for T-REX 550E/600E/600N/700E/700N.

Requirements:
700F3C Landing skid x 2

The below item also pairs actually well with the item being talked about.

New Landing Skid

This is an upgrade landing skid set for the Align 600 and 600N line of helicopters. More rigid than the basic landing gear these have a reduced height for a lower center of gravity better for 3D flying.

Package consists of:

2 - Black landing skids approximately 39g each.




Numerous others have actually purchased this item in addition to the item that you are presently checking out.

Landing Skid

Use for T-REX 550E/600E/600N/700E/700N.

Requirements:
Landing skid x 2

Below is another item that compliments the item being talked about.

Torque Tube

Use for T-REX 550E.

Requirements:
Torque tube x 1
Bearing MR148ZZ x 1(Φ8xΦ14x4mm)

This item compliments the above talked about item.

Cnc Slant Thread Main Drive Gear/ 112T

Use for T-REX 550E.
Should with CNC Slant Thread Main Drive Gear/112T(H60G001XXW).

Requirements:
Motor pinion gear 10T x 1
M4 set screw x 2(M4x4mm)

Below is another item that compliments the item being talked about.

M0.8 Torque Tube Front Drive Gear Set/34T

Use for T-REX 600PRO/600EFL PRO/550E

Specifications:
600PRO Front drive gear assembly x 1
600PRO Short umbrella gear x 1
600PRO Long umbrella gear x 1

This item compliments the main item below.

Torque Tube Rear Drive Gear Set

Use for T-REX 550/600 class.

Requirements:
Tail rotor shaft assembly x 1
Long umbrella gear x 1

Numerous others have actually purchased this item in addition to the item that you are presently checking out.

550 3G Carbon Fiber Blades

Use for T-REX 550E Helicopter

Requirements:
Forming: Symmetrical wing
Length:550x50x6.7mm
Width:12mm
Shaft Diameter:4mm
Weight:Appro 210g/set

Below is another item that compliments the item being talked about.

Tail Boom

Obtain T-REX 550E

Requirements:
Tail boom x 2(Φ20.3xΦ21.5x549mm)
Tail control guide x 2
Rudder control rod x 1(Φ1.96x575mm)
Ball Link x 2

This item compliments the above talked about item.

325 Carbon Fiber Blades

Apply to Trex450 all types

Specifications:
Forming: Symmetrical wing
Length:325x32mm
Width:4.7mm
Shaft Diameter:3mm
Weight: Appro 46g/set

Often purchased with the item that you are presently checking out.

600/700DFC Linkage Rod Set

Use for T-REX 600DFC(H60239A).
Use for T-REX 700DFC(H70089A).

Requirements:
700DFC Linkage rod A ? 4(M3x14mm)
Elevator ball link ? 4

This is a amazing enhancement to the item presently being talked about.

DS615 Servo Gear Set

Obtain ALIGN DS615 Servo

Specifications:
DS615 gear G1x1
DS615 gear G2x1
DS615 gear G3x1
DS615 gear G4x1

This is a amazing enhancement to the item presently being talked about.

Tail Boom Brace

Obtain T-REX 550E

Requirements:
Tail boom brace set x 2
Tail boom brace x 2(Φ1.9xΦ3.9x412mm)
Self tapping screw x 2(M3x10mm)
Self tapping screw x 2(T3x10mm)
M3 washer x 4(Φ3xΦ8x1mm)

Numerous others have actually purchased this item in addition to the item that you are presently checking out.

Carbon Vertical Stabilizer/1.6mm

Use for T-REX 550E.

Requirements:
3K vertical stabilizer x 1

Often purchased with the item that you are presently checking out.

550FL Flybarless Rotor Head System H55H002XX

Appropriate for T-REX 550L.
Should with 550 Main Shaft Set(H55H003XXW)、600PRO Metal Main Rotor Holder(H60204)、600 Feathering Shaft(H60H001XXW) or (H60006)

Requirements:
600FL Main Rotor Housing x 1
Feathering Shaft Sleeve x 1
600DFC Head Damper x 2
600 Head Damper x 2
600FL Main Blade Grip Arm x 2
600FL Linkage rod x 2
FL Metal Control Arm x 2
Collar x 2
FMR52ZZ Bearings x 4(Φ2xΦ5x2.3mm)
683ZZ Bearings x 4(Φ3xΦ7x3mm)
CCPM Metal Swashplate x 1
700 Elevator ball link x 10
600PRO Elevator ball link x 1
Linkage rod holder x 10
Linkage rod head x 2
5 Linkage ball B ? 2(M3x4)
700N Linkage ball B ? 2(M3x4)
Socket screw x 2(M4x8mm)
Socket screw x 4(M2x5mm)
Socket screw x 2(M3x16mm)
Socket button head collar screw x 1(M4x24mm)
Socket button head collar screw x 4(M3x6mm)
Washer x 2
M4 nut x 1