Align T-REX 700E PRO DFC Super Combo

Instruction(3GX Programmable Flybarless System) :
Brand new upgraded 3GX represents a brand-new generation of multi function flybarless system. The considerably enhanced performance will develop instant influence on any enthusiasts.
3GX is presently the tiniest and lightest flybarless system on the marketplace. 2 ports to directly connect Spektrum and JR satellite receivers, in addition to complete assistance of Futaba's S-BUS system.
Based on the 3G FL760 manual setup process, the 3GX can be setup in a couple of minutes through a simple process. In addition, the 3GX can support all the CCPM swashplate system presently on the marketplace consisting of 90, 120, 135, and 140 degrees swashplates.
Graphical highlighted instruction on the computer system setup software directs the user through a step by step setup process, allowing for fast setups without leaving out any actions.
Support Bluetooth connection. With the soon to be launched Bluetooth connection set, 3GX can be set wirelessly from a PC. Eventually there will also be smartphone apps allowing live adjustments to 3GX without powering down.
With 3GX's integrated in Align RCE-G600 governor function, no external governor is needed to reduce electronic wire clutters.
Customized criteria have been opened up in 3GX to allow pilots to fine tune various settings for swashplate and rudder. Settings export function permits custom settings to be shared among friends.
3GX uses brand new gyroscope sensors of the highest specifications when compared with other flybarless systems presently on the marketplace, allowing it to be used under severe conditions. Double axis plus rudder sensor considerably improves swashplate and rudder correction accuracy compared with last generation 3G. This is clearly noticeable in steady hover along with extremely aerobatic regimens.
Ideal for helicopter of all class from 250 to 800, radiance engine or electric powered. The exceptional vibration resistant quality is evident even when installed with more difficult double sided mounting tape.
3GX uses 16 bit processor which is 4 times faster than previous generation, in addition to an entirely re-written firmware. The outcome is a significant stability enhancement from previous generation, with stability that measures up to a flybarred helicopter, yet posses explosive agility.
With integrated in pirouette settlement function, 3GX is able to support the helicopter on a set point throughout pirouetting maneuvers. Pirouetting turns type of maneuvers are easily achieved with accuracy.
3GX's rudder permits constant rudder feel even under high speed conditions. This exceptional control feel will allow pilot of all skill levels to experience the ideal integration in between 3GX and helicopter.
Support with APS gyro system and raise more functions for your helicopter. With the APS gyro, the helicopter will have the ability to self support, hold position along with altitude, and even self-governing way point flights along with return home.

Specification(T-REX 700E DFC) :
1. Geared up with the low CG DFC rotor head, efficiently reduce wind resistance throughout flight, offering the most direct and accurate control feel back to the pilot, and exhibits exhilarating 3D performance and unthinkable flight speed.
2.Brand-new style swash anti-rotation guide with embedded anti-wear material, efficiently reduce the wear in between swashplate long ball and guide.
3.Geared up with brand new 700 3G carbonfiber primary blades designed particularly for extreme 3D flights, featuringagility and stability, and new graphics paint plan. The increased blade rigidness improves antitorsion characteristic throughout flight, and the new airfoil minimizes turbulencenear the blade tip, decreasing blade noise and power loss.
4.Brand new tailblade designed to sustain optimum tail locking performance under high headspeed and extreme flight conditions.
5. Brand new CCPM direct servo linkage style to remove the weight of double push-pull linkage system, making it possible for faster and more accurate control reaction.
6. Integrated servo mounts on the primary shaft bearing obstructs, allowing cyclic servos to be installed directly onto the bearing obstructs, which together with the composite material frame plates, producing a tidy and uncluttered look.
7. Utilizes composite carbon material integration method on frame structure for ease of upkeep and high rigidness. Increased front opening location to permit simpler battery setup.
8. Ingenious sliding battery tray rails anchored into the 3K side frames, with patented spring packed locking system, allowing for fast battery gain access to along with battery protection.
9. Top installed motor base bringing the motor's center of mass closer to turning disc, enhancing 3D agility and allowing blade drafts to cool the motor efficiently.
10. Motor mount consists of third bearing block to offer motor shaft assistance, efficiently reduce torque induced shifts, and reduce gear striping problem.
11. Utilizes high spec MOD1 112T CNC helical primary gear and MOD 1 tail drive helical gear to increase gear mesh location, and reduce gear noise throughout flight.
12. Top installed ESC platform to benefit from primary blades air flow for efficient cooling.
13. New lightweight H-shaped electric gadget retention system for protection, along with ergonomically correct style to simplify operation .
14.800MX includes high efficiency, exceptional power, exceptional torque, low present draw and low temperature; it?s efficient in keeping constant torque and head speed through constant 3D maneuvers.
15. Brand new transmission with more structured style also enables simpler disassembly.
16. High quality new tail gearbox style, integrated with new double point installed tail pitch control assembly to reduce slops and increase rudder control accuracy.
17. High torque rated one way bearing base.
18. High accuracy bearing supported double push point rudder control style.
19. High speed rated thrust bearings incorporated into tail blade grips.
20. Geared up with third bearing primary shaft assistance to increase rigidness, meeting the requirements of extreme 3D maneuvers.
21. New lightweight landing equipments.
22.Brand-new style wrap around airbrushed fiberglasscanopy, with aerodynamic form to reduce wind resistance. 4 point anti-vibration mounts for quickinstall and elimination.
23. New CNC aluminum alloy mounting plate.

Users need to have a particular concept of security to operate the R/C helicopters.
Be sure to read and adhere to associated security notes of user's manual prior to flying.

Specification(3GX Programmable Flybarless System) :
Running Temperature level:-10~60 degree
X and Y axis Operating Angle Range:-300~+300 degree
Z axis Operating Angle Range:-600~+600 degree
Size:36.5x25.2x15.6 mm Size
Weight11g Weight
Supports Wide/Narrow Bandwidth Digital and brushless servos
Spektrum and JR Satellite antennas support (Replaces initial factory receiver)
Futaba S.BUS system assistance
Built in governor function
Optimum working voltage:8.5V
Compatible with 1024/2048 resolution Spektrum receivers
Supports 90/120/135/140 CCPM swashplates
Field setup without making use of a PC
Compatible with 2 to 5 blades rotor heads
Support up to 6 servos
Automatic servo type recognization

Specification(T-REX 700E DFC) :
Length: 1350mm
Height: 360mm
Width: 208mm
Main Blade Length: 700mm
Main Rotor Diameter: 1582mm
Tail Rotor Diameter: 281mm
Motor Drive Equipment:12T
Main Drive Equipment:112T
Autorotation Tail Own Equipment: 104T
Tail Own Equipment: 22T
Drive Equipment Ratio: 1:9.33:4.37
Weight(With Motor): 3310g

Accessories:
T-REX 700E PRO DFC Packages Set x 1set
3GX Flybarless system x 1
700 3G Carbon Fiber Blades x 1set
DS615 digital servos x 3
DS655 Digital servo x 1
Aluminum Tail Boom x 1
3K Carbon Fiber Tail Boom x 1
800MX Brushless Motor(520KV) x 1
Castle EDGE HV 120 Brushless ESC x 1
6A External BEC w/ 5.1V Two-way Step-down voltage regulator x 1
105mm 3K Carbon Fiber Tail Blades x 1set Radio transmitter and electronic equipment required for assembly:
Transmitter(7-channel or more, helicopter system)
Receiver(7-channel or more)
6S Li-Po 4500 ~ 5200mAh x 2
TWO Li-Po 1900 ~ 2300mAh x 1
Dial Pitch Gauge