Align T-REX 700E DFC Flybarless HV Super Combo Kit w/Motor, ESC, 4 HV

This is the Align T-REX 700E DFC Flybarless HV Super Combo Helicopter Package. This extraordinary plan consists of not just the T-REX 700E DFC Package, however also aluminum and carbon fiber tail booms, a 690 3G carbon fiber blade set and a 105mm 3K carbon fiber tail blade set. This package also consists of an Align 530kV, 750MX brushless motor, a Castle Creations ICE2 HV 120 brushless ESC, three DS700 High Voltage Brushless digital cyclic servos and one DS750H High Voltage Brushless digital rudder servo. This extremely combination offers you with an amazing helicopter package and an equally impressive electronics and High Voltage plan all in the exact same box.

700E DFC Functions:

The Align 700E DFC helicopter is equipped with the low CG DFC rotor go to efficiently reduce wind resistance during flight and supply the most direct and precise control feel back to the pilot, supplying exhilarating 3D efficiency and unthinkable flight speed.
CCPM direct servo linkage design removes the weight of a double push-pull linkage system, for quick reaction and precise control.
Integrated servo mounts on the primary shaft bearing blocks permit the cyclic servos to be installed straight to the bearing blocks, and when combined with the composite material frame plates, creates a clean and uncluttered look.
The frame utilizes an integrated composite carbon material strategy for ease of maintenance and high rigidness, while the increased front opening location enables easy battery setup.
The innovative moving battery tray rails are imbedded into the 3K side frames, with a trademarked spring loaded latching system allowing for fast battery access in addition to battery protection.
A leading installed motor base brings the motor's center of mass closer to the rotating disc, enhancing 3D agility and enabling blade drafts to efficiently cool the motor.
The motor install system features a third bearing block to supply enhanced motor shaft assistance, lowering torque shift and minimizing the danger of striping an equipment.
The drive train features a high spec MOD1 112T CNC helical primary gear and a helical cut MOD1 tail drive gear to improve the gear mesh and reduce gear noise during flight.
A leading installed ESC platform utilizes the primary blade airflow for reliable ESC cooling.
The lightweight H-shaped electrical device retention system offers protection, in addition to an ergonomically proper design to streamline operation.
The consisted of Align 750MX brushless motor features a ribbed case and fan to significantly increase cooling and improve total power output.
The transmission features a structured design and permits easy disassembly.
The high quality tail transmission design, combined with a dual point installed tail pitch control assembly helps to reduce slop and increase rudder control.
The high torque ranked one method bearing base, bearing supported dual push point rudder control design, high speed ranked tail blade grip thrust bearings and a third bearing primary shaft assistance were consisted of to endure the abuse of extreme 3D flight.
A pre-painted high grade fiberglass canopy utilizes 4 point anti-vibration mounting system to permit effortless canopy setup. 

700E DFC Specifications:

Length: 1345mm

Height: 360mm

Width: 208mm

Main Blade Length: 690mm

Main Rotor Diameter: 1562mm

Tail Rotor Diameter: 281mm

Motor Drive Equipment: 12T

Main Drive Equipment: 112T

Autorotation Tail Drive Equipment: 104T

Tail Drive Equipment: 22T

Drive Equipment Ratio: 1:9.33:4.37

Weight (With Motor): 2900g

Consists of:

(1) T-REX 700E DFC Package
(1) Aluminum Tail Boom
(1) 3K Carbon Fiber Tail Boom
(1) 690 3G Carbon Fiber Blade Set
(1) 750MX Brushless Motor (530KV)
(3) DS700H High Voltage Brushless Servo
(1) DS750H High Voltage Brushless Servo


(1) Castle ICE2 HV 120 Brushless ESC
(1) 105mm 3K Carbon Fiber Tail Blade Set

Needed to Complete:

7-channel or more helicopter radio system
(2) SIX Li-Po 4500 ~ 5200mAh
(1) 2S Li-Po 1900 ~ 2300mAh
Dial Pitch Gauge or Digital Pitch Gauge