Align T-REX 700E DFC Flybarless HV Super Combo Kit w/Motor, ESC, 4 HV

This is the Align T-REX 700E DFC Flybarless HV Super Combination Helicopter Set. This amazing plan consists of not only the T-REX 700E DFC Set, but also aluminum and carbon fiber tail booms, a 690 3G carbon fiber blade set and a 105mm 3K carbon fiber tail blade set. This package also consists of an Align 530kV, 750MX brushless motor, a Castle Creations ICE2 HV 120 brushless ESC, three DS700 High Voltage Brushless digital cyclic servos and one DS750H High Voltage Brushless digital rudder servo. This super combination offers you with an unbelievable helicopter package and an equally impressive electronics and High Voltage plan all in the exact same box.

700E DFC Functions:

The Align 700E DFC helicopter is geared up with the low CG DFC rotor go to successfully decrease wind resistance during flight and supply the most direct and exact control feel back to the pilot, offering exhilarating 3D performance and unimaginable flight speed.
CCPM direct servo linkage design removes the weight of a double push-pull linkage system, for quick reaction and exact control.
Integrated servo installs on the primary shaft bearing blocks allow the cyclic servos to be mounted directly to the bearing blocks, when combined with the composite material frame plates, creates a tidy and uncluttered appearance.
The frame uses an integrated composite carbon material method for ease of maintenance and high rigidity, while the increased front opening location permits simple battery installation.
The ingenious sliding battery tray rails are inserted into the 3K side frames, with a patented spring packed latching system allowing for fast battery gain access to as well as battery protection.
A leading mounted motor base brings the motor's center of mass closer to the turning disc, enhancing 3D agility and permitting blade drafts to successfully cool the motor.
The motor mount system features a 3rd bearing block to supply enhanced motor shaft support, decreasing torque shift and lessening the danger of striping a gear.
The drive train features a high spec MOD1 112T CNC helical primary equipment and a helical cut MOD1 tail drive equipment to enhance the equipment mesh and minimize equipment noise during flight.
A leading mounted ESC platform uses the primary blade air flow for efficient ESC cooling.
The lightweight H-shaped electrical gadget retention system offers protection, as well as an ergonomically right design to streamline operation.
The consisted of Align 750MX brushless motor features a ribbed case and fan to dramatically increase cooling and enhance general power output.
The transmission features a structured design and enables simple disassembly.
The high quality tail gearbox design, combined with a dual point mounted tail pitch control assembly assists to minimize slop and increase rudder control.
The high torque ranked one way bearing base, bearing supported double push point rudder control design, high speed ranked tail blade grip thrust bearings and a 3rd bearing primary shaft support were consisted of to hold up against the abuse of extreme 3D flight.
A pre-painted high grade fiberglass canopy uses 4 point anti-vibration mounting system to allow effortless canopy installation. 

700E DFC Specifications:

Length: 1345mm

Height: 360mm

Width: 208mm

Main Blade Length: 690mm

Main Rotor Diameter: 1562mm

Tail Rotor Diameter: 281mm

Motor Drive Gear: 12T

Main Drive Gear: 112T

Autorotation Tail Drive Gear: 104T

Tail Drive Gear: 22T

Drive Gear Ratio: 1:9.33:4.37

Weight (With Motor): 2900g

Includes:

(1) T-REX 700E DFC Set
(1) Aluminum Tail Boom
(1) 3K Carbon Fiber Tail Boom
(1) 690 3G Carbon Fiber Blade Set
(1) 750MX Brushless Motor (530KV)
(3) DS700H High Voltage Brushless Servo
(1) DS750H High Voltage Brushless Servo


(1) Castle ICE2 HV 120 Brushless ESC
(1) 105mm 3K Carbon Fiber Tail Blade Set

Had to Total:

7-channel or more helicopter radio system
(2) SIX Li-Po 4500 ~ 5200mAh
(1) 2S Li-Po 1900 ~ 2300mAh
Dial Pitch Gauge or Digital Pitch Gauge