Align T-Rex 600 Nitro V2 "Limited Edition" Helicopter Combo

This is the Align T-Rex 600 Nitro V2 "Restricted Edition" Helicopter Combination Kit. The T-Rex 600N V2 is equipped with a re-designed rotor head system with numerous modification holes, allowing the device to be tweaked for either high control resolution or high stability based on the requirements of the individual pilot. Additionally, the T-REX 600N V2 comes with a range of performance upgrade parts for a restored look and enhanced performance. Plus, this combo plan consists of a 600D PRO Carbon fiber blade set, three DS610 digital cyclic servos, a DS620 digital rudder servo, the GP900 head lock gyro combo and a 2 In 1 voltage regulator combo!
600N V2 Includes:
600 sized programmable head assembly with 3 sets of positive and negative deltas, many Bell and Hiller mixing ratios available, together with numerous flybar ratio settings.
The head assembly enables pilots to take advantage of greater control resolution as well as stability level, satisfying the need of both highly steady static categories as well as precision aerobatic categories.
Dual 3K carbon plate side frame design for ease of maintenance and resistance to torque induced flex.
Additional radial bearing is added to the top of the primary equipment hub to guarantee steady rotation, and remove one way bearing jamming.
Re-designed unibody stainless steel tail drive equipment center mount, for more exact tail drive equipment and greater tolerance.
High quality carbon rudder control rod assembly utilizing 5mm carbon rod and metal ports, leading to enhanced rudder control precision.
Re-designed tail transmission, with aesthetically pleasing material and enhanced maintenance.
Efficient tail drive system.
High speed ranked thrust bearing in tail blade grips.
Highly effective lightened engine cooling fan, minimizing engine load and improving cooling efficiency.
Large diameter clutch system with unique installation technique for excellent balance, very little vibration, and effective power transfer.
Forward installed rudder servo to safeguard it from exhaust contamination.
95mm tail blades for sharp rudder action and excellent tail locking ability.
Unique H sample formed electronic installing platform for easy electronic installing and protection.
Large capacity 440cc fuel tank for approximately 10 minutes of severe 3D flights.
Starting and clutch supporting point makes use of 10mm one way bearing.
Ready to fly dry weight is just 3200g (7lbs).
Main fuel tank developed with fuel supply stabilization effect.
Light weight highly nimble flybar system.
Impact resistant fiberglass canopy with 3 point hook installing system for ease of install/removal.
Developed with ideas from big helicopter competitors, for the very best static and vibrant flight performance.
GP900 Head Lock Gyro Includes:
Uses MEMS (Micro Electro Mechanical Systems) micro electronic sensing units which are small, highly trusted, and highly steady.
16 bit high processing speed CPU is utilized for ultra high resolution, leading to greater rudder precision than formerly possible, even on contemporary high powered helicopters.
Supports Spektrum and JR satellites, standard receiver not needed.
Supports Futabs S-BUS system.
Supports both digital and analog servos.
Supports both wide and narrow band receivers.
Integrated RCE-G600 speed governor function, therefore GP900 can offer speed governor function without additional electronics.
Suitable for all 200 to 700 size radiance engine and electrical helicopters
Higher vibration resistance than other systems. Superior performance is possible even with more difficult installing foam tapes.
Support parameter setting through PC interface, as well as firmware updates.
Anti-torque payment. Ideal tail locking possible no matter if gyro is installed upright or inverted.
600N V2 Specs:

Length: 1160mm

Height: 398mm

Main blade length: 600mm

Main rotor diameter: 1350mm

Tail rotor diameter: 240mm

Engine pinion equipment: 20T

Autorotation tail drive equipment: 180T

Drive equipment ratio: 8.5:1:4.5(E:M:T)

Flying weight: Approximate. 3200g
GP900 Specs:

Operating Voltage: DC 3.5~8.4V

Present Intake: <80mA @ 4.8V

Angular Detection Speed: 600 degrees/sec

Operating Humidity: -20℃~65℃

RoHS certification: Yes

Operating Humidity: 0%~95%

Size: 36.5x25.2x15.6mm

Weight: 11g
Includes:
(1) T-REX 600 Nitro V2 kit
(1) 600D PRO Carbon fiber blade set
(3) DS610 Digital servo
(1) DS620 Digital servo
(1) GP900 Head lock gyro combo
(1) 2 In 1 voltage regulator combo
Needed to Complete:
7-channel or more, helicopter radio system
(1) Standard servo
(1) .50 class engine
(1) .50 class muffler
(1) Pitch gauge
(1) Super starter
Fuel & Fuel pump