Align T-Rex 600 Nitro V2 "Limited Edition" Helicopter Combo

This is the Align T-Rex 600 Nitro V2 "Limited Edition" Helicopter Combo Set. The T-Rex 600N V2 is equipped with a re-designed rotor head system with multiple modification holes, allowing the machine to be tweaked for either high control resolution or high stability based on the requirements of the individual pilot. Additionally, the T-REX 600N V2 includes a range of performance upgrade elements for a renewed look and enhanced performance. Plus, this combo plan consists of a 600D PRO Carbon fiber blade set, 3 DS610 digital cyclic servos, a DS620 digital rudder servo, the GP900 head lock gyro combo and a 2 In 1 voltage regulator combo!
600N V2 Includes:
600 sized programmable head assembly with 3 sets of favorable and negative deltas, many Bell and Hiller mixing ratios offered, in addition to numerous flybar ratio settings.
The head assembly enables pilots to take advantage of higher control resolution in addition to stability level, satisfying the requirement of both highly steady fixed categories in addition to accuracy aerobatic categories.
Dual 3K carbon plate side frame design for ease of maintenance and resistance to torque caused flex.
Additional radial bearing is contributed to the top of the primary gear center to make sure steady rotation, and eliminate one way bearing jamming.
Re-designed unibody stainless steel tail drive gear center mount, for more precise tail drive gear and higher tolerance.
High quality carbon rudder control rod assembly using 5mm carbon rod and metal adapters, leading to enhanced rudder control precision.
Re-designed tail transmission, with visually pleasing material and enhanced maintenance.
Efficient tail drive system.
High speed ranked thrust bearing in tail blade grips.
Highly effective lightened engine cooling fan, reducing engine load and enhancing cooling efficiency.
Large diameter clutch system with special installation method for great balance, very little vibration, and reliable power transfer.
Forward mounted rudder servo to secure it from exhaust contamination.
95mm tail blades for sharp rudder reaction and exceptional tail locking ability.
Unique H cross section formed electronic installing platform for simple electronic installing and protection.
Large capacity 440cc fuel tank for up to 10 minutes of extreme 3D flights.
Starting and clutch supporting point utilizes 10mm one way bearing.
Ready to fly dry weight is just 3200g (7lbs).
Main fuel tank created with fuel supply stabilization effect.
Light weight highly nimble flybar system.
Impact resistant fiberglass canopy with 3 point hook installing system for ease of install/removal.
Developed with ideas from large helicopter competitors, for the best fixed and vibrant flight performance.
GP900 Head Lock Gyro Includes:
Uses MEMS (Micro Electro Mechanical Systems) micro electronic sensors which are small, highly reliable, and highly steady.
16 bit high processing speed CPU is used for ultra high resolution, leading to higher rudder accuracy than previously possible, even on modern high powered helicopters.
Supports Spektrum and JR satellites, conventional receiver not needed.
Supports Futabs S-BUS system.
Supports both digital and analog servos.
Supports both broad and narrow band receivers.
Integrated RCE-G600 speed governor function, thus GP900 can offer speed governor function without extra electronics.
Suitable for all 200 to 700 size glow engine and electric helicopters
Higher vibration resistance than any other systems. Superior performance is possible even with more difficult installing foam tapes.
Support specification setting through PC interface, in addition to firmware updates.
Anti-torque settlement. Optimal tail locking possible no matter if gyro is mounted upright or inverted.
600N V2 Requirements:

Length: 1160mm

Height: 398mm

Main blade length: 600mm

Main rotor diameter: 1350mm

Tail rotor diameter: 240mm

Engine pinion gear: 20T

Autorotation tail drive gear: 180T

Drive gear ratio: 8.5:1:4.5(E:M:T)

Flying weight: Approximate. 3200g
GP900 Requirements:

Operating Voltage: DC 3.5~8.4V

Current Consumption: <80mA @ 4.8V

Angular Detection Speed: 600 degrees/sec

Operating Humidity: -20℃~65℃

RoHS certification: Yes

Operating Humidity: 0%~95%

Size: 36.5x25.2x15.6mm

Weight: 11g
Includes:
(1) T-REX 600 Nitro V2 kit
(1) 600D PRO Carbon fiber blade set
(3) DS610 Digital servo
(1) DS620 Digital servo
(1) GP900 Head lock gyro combo
(1) 2 In 1 voltage regulator combo
Needed to Complete:
7-channel or more, helicopter radio system
(1) Standard servo
(1) .50 class engine
(1) .50 class muffler
(1) Pitch gauge
(1) Super starter
Fuel & Fuel pump