Align T-Rex 600 Nitro V2 "Limited Edition" Helicopter Combo

This is the Align T-Rex 600 Nitro V2 "Minimal Edition" Helicopter Combination Set. The T-Rex 600N V2 is geared up with a re-designed rotor head system with numerous change holes, allowing the device to be tweaked for either high control resolution or high stability based upon the requirements of the individual pilot. In addition, the T-REX 600N V2 comes with a variety of efficiency upgrade parts for a renewed appearance and enhanced efficiency. Plus, this combo plan consists of a 600D PRO Carbon fiber blade set, three DS610 digital cyclic servos, a DS620 digital rudder servo, the GP900 head lock gyro combo and a 2 In 1 voltage regulator combo!
600N V2 Includes:
600 sized programmable head assembly with 3 sets of favorable and unfavorable deltas, many Bell and Hiller blending ratios offered, in addition to various flybar ratio settings.
The head assembly allows pilots to benefit from greater control resolution along with stability level, satisfying the need of both extremely stable fixed categories along with precision aerobatic categories.
Dual 3K carbon plate side frame design for ease of upkeep and resistance to torque induced flex.
Additional radial bearing is added to the top of the primary equipment hub to guarantee stable rotation, and eliminate one method bearing jamming.
Re-designed unibody stainless-steel tail drive equipment center mount, for more accurate tail drive equipment and greater tolerance.
High quality carbon rudder control rod assembly utilizing 5mm carbon rod and metal adapters, leading to enhanced rudder control precision.
Re-designed tail transmission, with visually pleasing material and enhanced maintenance.
Efficient tail drive system.
High speed rated thrust bearing in tail blade grips.
Highly effective lightened engine cooling fan, minimizing engine load and improving cooling efficiency.
Large size clutch system with unique installation approach for great balance, minimal vibration, and reliable power transfer.
Forward mounted rudder servo to safeguard it from exhaust contamination.
95mm tail blades for sharp rudder action and outstanding tail locking ability.
Unique H sample shaped electronic installing platform for easy electronic installing and protection.
Large capacity 440cc fuel tank for approximately 10 minutes of extreme 3D flights.
Starting and clutch supporting point uses 10mm one method bearing.
Ready to fly dry weight is only 3200g (7lbs).
Main fuel tank developed with fuel supply stabilization effect.
Light weight extremely nimble flybar system.
Impact resistant fiberglass canopy with 3 point hook installing system for ease of install/removal.
Created with ideas from large helicopter competitors, for the very best fixed and dynamic flight performance.
GP900 Head Lock Gyro Includes:
Uses MEMS (Micro Electro Mechanical Systems) micro electronic sensors which are little, extremely trusted, and extremely stable.
16 bit high processing speed CPU is used for ultra high resolution, leading to greater rudder precision than formerly possible, even on modern-day high powered helicopters.
Supports Spektrum and JR satellites, traditional receiver not needed.
Supports Futabs S-BUS system.
Supports both digital and analog servos.
Supports both wide and narrow band receivers.
Integrated RCE-G600 speed governor function, thus GP900 can offer speed governor function without extra electronics.
Suitable for all 200 to 700 size glow engine and electrical helicopters
Higher vibration resistance than any other systems. Superior efficiency is achievable even with more difficult installing foam tapes.
Support specification setting through PC interface, along with firmware updates.
Anti-torque payment. Optimum tail locking achievable no matter if gyro is mounted upright or inverted.
600N V2 Requirements:

Length: 1160mm

Height: 398mm

Main blade length: 600mm

Main rotor size: 1350mm

Tail rotor size: 240mm

Engine pinion equipment: 20T

Autorotation tail drive equipment: 180T

Drive equipment ratio: 8.5:1:4.5(E:M:T)

Flying weight: Approximate. 3200g
GP900 Requirements:

Running Voltage: DC 3.5~8.4V

Current Intake: <80mA @ 4.8V

Angular Detection Speed: 600 degrees/sec

Operating Humidity: -20℃~65℃

RoHS certification: Yes

Operating Humidity: 0%~95%

Size: 36.5x25.2x15.6mm

Weight: 11g
Includes:
(1) T-REX 600 Nitro V2 kit
(1) 600D PRO Carbon fiber blade set
(3) DS610 Digital servo
(1) DS620 Digital servo
(1) GP900 Head lock gyro combo
(1) 2 In 1 voltage regulator combo
Needed to Complete:
7-channel or more, helicopter radio system
(1) Standard servo
(1) .50 class engine
(1) .50 class muffler
(1) Pitch gauge
(1) Super starter
Fuel & Fuel pump