Align T-Rex 600 Nitro V2 "Limited Edition" Helicopter Combo

This is the Align T-Rex 600 Nitro V2 "Minimal Edition" Helicopter Combo Set. The T-Rex 600N V2 is equipped with a re-designed rotor head system with multiple adjustment holes, allowing the device to be fine tuned for either high control resolution or high stability based upon the requirements of the specific pilot. Additionally, the T-REX 600N V2 comes with a variety of performance upgrade elements for a renewed appearance and improved performance. Plus, this combination plan consists of a 600D PRO Carbon fiber blade set, three DS610 digital cyclic servos, a DS620 digital rudder servo, the GP900 head lock gyro combination and a 2 In 1 voltage regulator combination!
600N V2 Features:
600 sized programmable head assembly with 3 sets of positive and negative deltas, many Bell and Hiller blending ratios available, along with numerous flybar ratio settings.
The head assembly permits pilots to gain from greater control resolution in addition to stability level, satisfying the need of both highly steady static categories in addition to precision aerobatic categories.
Dual 3K carbon plate side frame design for ease of upkeep and resistance to torque induced flex.
Additional radial bearing is contributed to the top of the primary equipment hub to guarantee steady rotation, and get rid of one way bearing jamming.
Re-designed unibody stainless-steel tail drive equipment center install, for more accurate tail drive equipment and greater tolerance.
High quality carbon rudder control rod assembly using 5mm carbon rod and metal connectors, resulting in improved rudder control precision.
Re-designed tail transmission, with aesthetically pleasing product and improved maintenance.
Efficient tail drive system.
High speed rated thrust bearing in tail blade grips.
Highly effective lightened engine cooling fan, reducing engine load and enhancing cooling efficiency.
Large size clutch system with unique setup approach for excellent balance, very little vibration, and effective power transfer.
Forward installed rudder servo to secure it from exhaust contamination.
95mm tail blades for sharp rudder response and exceptional tail locking ability.
Unique H cross section shaped electronic installing platform for easy electronic installing and protection.
Large capacity 440cc fuel tank for approximately 10 minutes of extreme 3D flights.
Starting and clutch supporting point uses 10mm one way bearing.
Ready to fly dry weight is only 3200g (7lbs).
Main fuel tank designed with fuel supply stabilization effect.
Light weight highly agile flybar system.
Impact resistant fiberglass canopy with 3 point hook installing system for ease of install/removal.
Developed with principles from big helicopter competitions, for the very best static and vibrant flight performance.
GP900 Head Lock Gyro Features:
Uses MEMS (Micro Electro Mechanical Systems) micro electronic sensing units which are little, highly trustworthy, and highly steady.
16 bit high processing speed CPU is used for ultra high resolution, resulting in greater rudder precision than formerly possible, even on contemporary high powered helicopters.
Supports Spektrum and JR satellites, conventional receiver not needed.
Supports Futabs S-BUS system.
Supports both digital and analog servos.
Supports both wide and narrow band receivers.
Integrated RCE-G600 speed governor function, thus GP900 can provide speed governor function without extra electronics.
Suitable for all 200 to 700 size radiance engine and electrical helicopters
Greater vibration resistance than other systems. Superior performance is achievable even with harder installing foam tapes.
Support parameter setting through PC interface, in addition to firmware updates.
Anti-torque payment. Optimum tail locking achievable no matter if gyro is installed upright or inverted.
600N V2 Specs:

Length: 1160mm

Height: 398mm

Main blade length: 600mm

Main rotor size: 1350mm

Tail rotor size: 240mm

Engine pinion equipment: 20T

Autorotation tail drive equipment: 180T

Drive equipment ratio: 8.5:1:4.5(E:M:T)

Flying weight: Approximate. 3200g
GP900 Specs:

Operating Voltage: DC 3.5~8.4V

Present Consumption: <80mA @ 4.8V

Angular Detection Speed: 600 degrees/sec

Operating Humidity: -20℃~65℃

RoHS certification: Yes

Operating Humidity: 0%~95%

Size: 36.5x25.2x15.6mm

Weight: 11g
Includes:
(1) T-REX 600 Nitro V2 kit
(1) 600D PRO Carbon fiber blade set
(3) DS610 Digital servo
(1) DS620 Digital servo
(1) GP900 Head lock gyro combo
(1) 2 In 1 voltage regulator combo
Needed to Complete:
7-channel or more, helicopter radio system
(1) Standard servo
(1) .50 class engine
(1) .50 class muffler
(1) Pitch gauge
(1) Super starter
Fuel & Fuel pump