Align T-REX 500X TOP Combo (BL80A ESC)

Experienced in numerous of developments, the brand new T-REX 500XT is now prepared to go. More attractive and innovative style ideas are all in here, it definitely would be your favorite T-REX 500XT design ever.

Refresh and fine-tune, T-REX 500XT adapt with brand new FL rotor head system, uses a very low CG style which reduces resistance during 3D maneuvers while increasing flight responsiveness and precision. A progressive style includes a gloss silver and red anodizing appearance which continue our quality development based upon our 700 class helicopter. The T-REX 500XT primary frame uses composite product integration technology on carbon side frame plates, including the addition of battery mounting side rails, and a top motor mount style. Ingenious adjustable belt guide pulley, permits a practical way to change the belt stress by releasing or tightening up the screw. The screw is utilized to maintain optimum belt stress in time to keep the best. Also T-REX 500XT landing skid is slanted 5 degrees forward to improve crashworthiness.

T-REX 500XT uses 470mm primary blades and 520MX(1600KV/3527) motor with 20% power upgrades than the initial 1600KV/3225 motor. The most recent new RCE-BL80A Brushless ESC assistance dual BEC output from 5 ~ 8V providing efficient and superior power. The NEW DS530M/DS535M digital servos are with extreme torque and speed action enable to support faster, more precise and precise flight performance.

Equipped with all the top end electronic devices, T-REX 500XT is as stable and powerful like the large scale helicopters. It is about to re-define the 500-class helicopters in your mind.

New extended 470mm primary blades for T-REX 500XT efficiently improve the flying stability and power efficiency. Boost the power for better control enable to delight in T-REX 500XT flights exact same like other large size helicopters.
New 78 size tail blades are longer in length and deal superior and precise tail holding efficiency, even during demanding 3D flight.

The brand new low CG 500FL Flybarless Rotor Head System uses the precision grinding of high-carbon steel hollow shaft efficiently increase its concentricity. Enable to decrease resistance during 3D maneuvers, increased flight responsiveness and precision. In addition, the styling appearance consistency with red anodized and stainless color, draw out the high quality similar to 700 size 3D helicopter.

New Swashplate style with precise bearings features in zero slop providing a precise and precise regulated flight.

New 520MX(1600KV/3527) motor features high performance, superior power, outstanding torque, low existing draw, and a low operating temperature. Enable to supply preserving consistent torque and head speed through continuous 3D maneuvers.

Brand new CNC metal reinforcement plate and brace compare with frame mounting bolt efficiently increase the torsional strength of primary frame, under extreme 3D maneuver, you can strongly feel its strong reinforcement from its structure. In addition, the styling appearance consistency with red anodized and stainless color draw out the high tactile appeal.
Carbon fiber side frame plates are produced using a proprietary composite product integration technology which integrates the battery mounting rails into the frame. This unique usage of open areas within the frame creates a rigid frame and is visually pleasing.

An extra 3rd primary shaft bearing block increases the strength of the primary frame while enhancing 3D flight.

RCE-BL80A is specifically created for T-REX 500XT providing greater currency output and assistance for high voltage servos with an internal BEC output from 6V to 8.4V which can be established based upon servo specification.

Brand new locking battery tray which uses integrated mounting rails inside the frames to streamline insertion / elimination of battery while providing defense for the battery.

DS530M HV Cyclic and DS535M HV Rudder servos support as much as 8.4V for superior responsiveness, extreme torque, and improved performance.

Innovative adjustable belt guide pulley, permits a practical way to change the belt stress by releasing or tightening up the screw. The screw is utilized to maintain optimum belt stress over time.
Brand New Belt Drive Assembly style permit peaceful operation and low cost on serviceability.

Ultilize of strengthen primary equipment case features in using bigger bearing has a higher load bring capability which reduces the loss of momentum and improves the performance, speed, and smoothness of the primary rotor. The new primary equipment case and all-metal main pulley transmission system is an effective style to deliver the supreme performance.

Landing skid is slanted 5 degrees forward to improve crashworthiness.

A 19mm wide Tail Boom to improves the torsional strength.
Carbon Fiber Tail Control Rod is useful and improves the helicopters tail control.

The freshly created dual point supported tail control assembly delivers slop free efficiency while enhancing rudder resolution and precision.

The new tail rotor holder style includes thrust bearings which increases sturdiness, as well as significantly enhancing the precision and performance of the tail efficiency when using 78 size Tail Blades.

Standard equipment

Microbeast PLUS Flybarless System x 1 set
RCE-BL80A Brushless ESC x 1
520MX Brushless Motor(1600KV/3527) x 1
DS530M Digital servo x 3
DS535M Digital servo x 1

Specification
Length: 935mm
Height: 259mm
Width: 151mm
Main Blade Length: 470mm
Main Rotor Diameter: 1054mm
Tail Rotor Diameter: 219mm
Motor Pinion Equipment: 12T
Main Drive Equipment: 134T
Main Drive Pulley-block: 80T
Tail Drive Equipment: 21T
Drive Equipment Ratio: 11.17:1:3.81
Weight(w/o battery): approx. 1450gAccessories

T-REX 500X PACKAGE Set x 1 
Microbeast PLUS Flybarless System x 1 set
470 Carbon Fiber Blades x 1
78 Tail Rotor Blade x 1
520MX Brushless Motor(1600KV/3527) x 1
DS530M Digital servo x 3
DS535M Digital servo x 1 
RCE-BL80A Brushless ESC x 1

Radio transmitter and electronic equipment required for assembly:
Transmitter(6-channel or more, helicopter system)
Receiver(6-channel or more)
SIX Li-Po 2600 ~ 3300mAh (3300mAh tip)
Digital Pitch Gauge