Align T-REX 500X Super Combo (Metal Case Servos)

Experienced in many of innovations, the brand new T-REX 500X is now ready to go. More attractive and imaginative design concepts are all in here, it definitely would be your preferred T-REX 500X model ever.

Refresh and fine-tune, T-REX 500X adjust with brand new FL rotor head system, uses an incredibly low CG design which lowers resistance during 3D maneuvers while increasing flight responsiveness and accuracy. A progressive design includes a gloss silver and red anodizing appearance which continue our quality development based on our 700 class helicopter. The T-REX 500X primary frame uses composite material combination innovation on carbon side frame plates, including the addition of battery mounting side rails, and a top motor install design. Ingenious adjustable belt guide wheel, enables a hassle-free method to change the belt tension by launching or tightening the screw. The screw is utilized to keep ideal belt tension in time to keep the best. Likewise T-REX 500X landing skid is slanted 5 degrees forward to enhance crashworthiness.

T-REX 500X uses 470mm primary blades and 520MX(1600KV/3527) motor with 20% power upgrades than the initial 1600KV/3225 motor. The most recent new RCE-BL80X Brushless ESC support double BEC output from 6 ~ 8.4V supplying effective and superior power. The NEW DS530M/DS535M digital servos are with severe torque and speed action allow to support quicker, more precise and accurate flight performance.

Equipped with all the leading end electronic gadgets, T-REX 500X is as stable and powerful like the big scale helicopters. It will re-define the 500-class helicopters in your mind.

New extended 470mm primary blades for T-REX 500X successfully enhance the flying stability and power performance. Improve the power for much better control allow to take pleasure in T-REX 500X flights very same like other large size helicopters.

New 78 size tail blades are longer in length and deal superior and precise tail holding performance, even during requiring 3D flight.

The brand new low CG 500FL Flybarless Rotor Head System uses the accuracy grinding of high-carbon steel hollow shaft successfully increase its concentricity. Allow to decrease resistance during 3D maneuvers, increased flight responsiveness and accuracy. In addition, the styling appearance harmony with red anodized and stainless color, draw out the high quality much like 700 size 3D helicopter.

New Swashplate design with precise bearings functions in zero slop delivering an exact and accurate regulated flight.

New 520MX(1600KV/3527) motor includes high efficiency, superior power, exceptional torque, low current draw, and a low operating temperature level. Allow to provide keeping constant torque and head speed through constant 3D maneuvers.

Brand new CNC metal support plate and brace compare to frame mounting bolt successfully increase the torsional stength of primary frame, under severe 3D maneuver, you can highly feel its strong support from its structure. In addition, the styling appearance harmony with red anodized and stainless color draw out the high tactile appeal.
Carbon fiber side frame plates are manufactured using a proprietary composite material combination innovation which incorporates the battery mounting rails into the frame. This special use of open areas within the frame creates a rigid frame and is visually pleasing.

An additional 3rd primary shaft bearing block increases the strength of the primary frame while enhancing 3D flight.

RCE-BL80X is specifically created for T-REX 500X supplying greater currency output and support for high voltage servos with an internal BEC output from 6V to 8.4V which can be established based on servo specification.

Brand new latching battery tray which uses incorporated mounting rails inside the frames to simplify insertion / removal of battery while supplying protection for the battery.

DS530M HV Cyclic and DS535M HV Rudder servos support up to 8.4V for superior responsiveness, severe torque, and improved performance.

Innovative adjustable belt guide wheel, enables a hassle-free method to change the belt tension by launching or tightening the screw. The screw is utilized to keep ideal belt tension over time.
Brand New Belt Drive Assembly design allow for quiet operation and low cost on serviceability.

Ultilize of enhance primary equipment case functions in using larger bearing has a greater load bring capacity which lowers the loss of momentum and enhances the fficiency, speed, and smoothness of the primary rotor. The new primary equipment case and all-metal main wheel transmission system is an effective design to provide the ultimate performance.

Landing skid is slanted 5 degrees forward to enhance crashworthiness.

A 19mm wide Tail Boom to enhances the torsional strength.
Carbon Fiber Tail Control Rod is practical and enhances the helicopters tail control.

The newly created double point supported tail control assembly provides slop totally free performance while enhancing rudder resolution and precision.

The new tail rotor holder design includes thrust bearings which increases toughness, in addition to substantially enhancing the precision and efficiency of the tail performance when using 78 size Tail Blades.

Specification
? Length: 935mm
? Height: 259mm
? Width: 151mm
? Main Blade Length: 470mm
? Main Rotor Size: 1054mm
? Tail Rotor Size: 219mm
? Motor Pinion Equipment: 12T
? Main Drive Equipment: 134T
? Main Drive Pulley-block: 80T
? Tail Drive Equipment: 21T
? Drive Equipment Ratio: 11.17:1:3.81
? Weight(w/o battery): approx. 1450gAccessories

?T-REX 500X SET Set x 1 
?Microbeast PLUS Flybarless System x 1 set
?470 Carbon Fiber Blades x 1
?78 Tail Rotor Blade x 1
?520MX Brushless Motor(1600KV/3527) x 1
?DS530M Digital servo x 3
?DS535M Digital servo x 1 
?RCE-BL80X Brushless ESC x 1

Radio transmitter and electronic equipment needed for assembly:
?Transmitter(7-channel or more, helicopter system)
?Receiver(7-channel or more)
?6S Li-Po 2600 ~ 3300mAh (3300mAh recommendation)
?Digital Pitch Gauge