Align T-REX 500X Super Combo (Metal Case Servos)

Experienced in numerous of innovations, the brand new T-REX 500X is now prepared to go. More appealing and innovative design ideas are all in here, it absolutely would be your preferred T-REX 500X design ever.

Refresh and fine-tune, T-REX 500X adjust with brand new FL rotor head system, uses an exceptionally low CG design which minimizes resistance during 3D maneuvers while increasing flight responsiveness and precision. A progressive design includes a gloss silver and red anodizing appearance which continue our quality advancement based upon our 700 class helicopter. The T-REX 500X primary frame uses composite product integration innovation on carbon side frame plates, including the addition of battery installing side rails, and a top motor install design. Ingenious adjustable belt guide sheave, permits a convenient method to adjust the belt tension by releasing or tightening up the screw. The screw is used to maintain optimal belt tension gradually to keep the very best. Likewise T-REX 500X landing skid is slanted 5 degrees forward to enhance crashworthiness.

T-REX 500X uses 470mm primary blades and 520MX(1600KV/3527) motor with 20% power upgrades than the original 1600KV/3225 motor. The current new RCE-BL80X Brushless ESC support double BEC output from 6 ~ 8.4V providing efficient and superior power. The NEW DS530M/DS535M digital servos are with extreme torque and speed response enable to support quicker, more accurate and precise flight performance.

Equipped with all the top end electronic devices, T-REX 500X is as steady and powerful like the big scale helicopters. It is about to re-define the 500-class helicopters in your mind.

New extended 470mm primary blades for T-REX 500X successfully enhance the flying stability and power performance. Boost the power for much better control enable to enjoy T-REX 500X flights same like other large size helicopters.

New 78 size tail blades are longer in length and offer superior and accurate tail holding performance, even during requiring 3D flight.

The brand new low CG 500FL Flybarless Rotor Head System uses the precision grinding of high-carbon steel hollow shaft successfully increase its concentricity. Permit to decrease resistance during 3D maneuvers, increased flight responsiveness and precision. In addition, the styling appearance harmony with red anodized and stainless color, draw out the high quality similar to 700 size 3D helicopter.

New Swashplate design with accurate bearings features in zero slop delivering an accurate and precise controlled flight.

New 520MX(1600KV/3527) motor includes high performance, superior power, excellent torque, low current draw, and a low operating temperature. Permit to provide maintaining consistent torque and head speed through constant 3D maneuvers.

Brand new CNC metal support plate and brace compare with frame installing bolt successfully increase the torsional stength of primary frame, under extreme 3D maneuver, you can strongly feel its strong support from its structure. In addition, the styling appearance harmony with red anodized and stainless color draw out the high tactile appeal.
Carbon fiber side frame plates are made using an exclusive composite product integration innovation which incorporates the battery installing rails into the frame. This unique use of open spaces within the frame develops a rigid frame and is visually pleasing.

An additional 3rd primary shaft bearing block increases the strength of the primary frame while improving 3D flight.

RCE-BL80X is specifically created for T-REX 500X providing higher currency output and support for high voltage servos with an internal BEC output from 6V to 8.4V which can be established based upon servo specification.

Brand new latching battery tray which uses incorporated installing rails inside the frames to streamline insertion / removal of battery while providing defense for the battery.

DS530M HV Cyclic and DS535M HV Rudder servos support approximately 8.4V for superior responsiveness, extreme torque, and enhanced performance.

Innovative adjustable belt guide sheave, permits a convenient method to adjust the belt tension by releasing or tightening up the screw. The screw is used to maintain optimal belt tension over time.
Brand New Belt Drive Assembly design permit peaceful operation and low cost on serviceability.

Ultilize of enhance primary equipment case features in using larger bearing has a higher load bring capacity which minimizes the loss of momentum and improves the fficiency, speed, and smoothness of the primary rotor. The new primary equipment case and all-metal main sheave transmission system is an effective design to provide the ultimate performance.

Landing skid is slanted 5 degrees forward to enhance crashworthiness.

A 19mm broad Tail Boom to improves the torsional strength.
Carbon Fiber Tail Control Rod is useful and improves the helicopters tail control.

The recently created double point supported tail control assembly provides slop complimentary performance while improving rudder resolution and precision.

The new tail rotor holder design consists of thrust bearings which increases durability, along with substantially improving the precision and performance of the tail performance when using 78 size Tail Blades.

Specification
? Length: 935mm
? Height: 259mm
? Width: 151mm
? Main Blade Length: 470mm
? Main Rotor Diameter: 1054mm
? Tail Rotor Diameter: 219mm
? Motor Pinion Gear: 12T
? Main Drive Gear: 134T
? Main Drive Sheave: 80T
? Tail Own Gear: 21T
? Own Gear Ratio: 11.17:1:3.81
? Weight(w/o battery): approx. 1450gAccessories

?T-REX 500X PACKAGE Set x 1 
?Microbeast PLUS Flybarless System x 1 set
?470 Carbon Fiber Blades x 1
?78 Tail Rotor Blade x 1
?520MX Brushless Motor(1600KV/3527) x 1
?DS530M Digital servo x 3
?DS535M Digital servo x 1 
?RCE-BL80X Brushless ESC x 1

Radio transmitter and electronic equipment required for assembly:
?Transmitter(7-channel or more, helicopter system)
?Receiver(7-channel or more)
?6S Li-Po 2600 ~ 3300mAh (3300mAh suggestion)
?Digital Pitch Gauge