Align T-REX 500X Super Combo

Experienced in various of developments, the brand new T-REX 500X is now ready to go. More attractive and innovative style ideas are all in here, it absolutely would be your preferred T-REX 500X design ever.

Refresh and improve, T-REX 500X adjust with brand new FL rotor head system, makes use of an incredibly low CG style which lowers resistance throughout 3D maneuvers while increasing flight responsiveness and accuracy. A progressive style adds a gloss silver and red anodizing look which continue our quality advancement based upon our 700 class helicopter. The T-REX 500X primary frame makes use of composite material combination innovation on carbon side frame plates, consisting of the addition of battery mounting side rails, and a top motor install style. Ingenious adjustable belt guide pulley, enables a hassle-free method to adjust the belt tension by launching or tightening the screw. The screw is used to preserve optimum belt tension with time to keep the best. Also T-REX 500X landing skid is slanted 5 degrees forward to improve crashworthiness.

T-REX 500X makes use of 470mm primary blades and 520MX(1600KV/3527) motor with 20% power upgrades than the original 1600KV/3225 motor. The most recent new RCE-BL80X Brushless ESC support double BEC output from 6 ~ 8.4V offering effective and remarkable power. The NEW DS530M/DS535M digital servos are with severe torque and speed response allow to support much faster, more exact and accurate flight performance.

Equipped with all the top end electronic gadgets, T-REX 500X is as stable and effective like the large scale helicopters. It will re-define the 500-class helicopters in your mind.

New extended 470mm primary blades for T-REX 500X successfully improve the flying stability and power efficiency. Enhance the power for better control allow to enjoy T-REX 500X flights exact same like other large size helicopters.

New 78 size tail blades are longer in length and deal remarkable and exact tail holding efficiency, even throughout requiring 3D flight.

The brand new low CG 500FL Flybarless Rotor Head System makes use of the accuracy grinding of high-carbon steel hollow shaft successfully increase its concentricity. Enable to minimize resistance throughout 3D maneuvers, increased flight responsiveness and accuracy. In addition, the styling look consistency with red anodized and stainless color, bring out the high quality much like 700 size 3D helicopter.

New Swashplate style with exact bearings functions in no slop providing an accurate and accurate regulated flight.

New 520MX(1600KV/3527) motor features high efficiency, remarkable power, exceptional torque, low present draw, and a low operating temperature. Enable to offer preserving constant torque and head speed through constant 3D maneuvers.

Brand new CNC metal support plate and brace compare to frame mounting bolt successfully increase the torsional stength of primary frame, under severe 3D maneuver, you can strongly feel its solid support from its structure. In addition, the styling look consistency with red anodized and stainless color bring out the high tactile appeal.
Carbon fiber side frame plates are produced using an exclusive composite material combination innovation which incorporates the battery mounting rails into the frame. This distinct use of open areas within the frame develops a rigid frame and is visually pleasing.

An additional 3rd primary shaft bearing block increases the strength of the primary frame while enhancing 3D flight.

RCE-BL80X is specially designed for T-REX 500X offering greater currency output and support for high voltage servos with an internal BEC output from 6V to 8.4V which can be established based upon servo specification.

Brand new latching battery tray which makes use of integrated mounting rails inside the frames to simplify insertion / removal of battery while offering protection for the battery.

DS530 HV Cyclic and DS535 HV Rudder servos support up to 8.4V for remarkable responsiveness, severe torque, and enhanced performance.

Innovative adjustable belt guide pulley, enables a hassle-free method to adjust the belt tension by launching or tightening the screw. The screw is used to preserve optimum belt tension over time.
Brand New Belt Drive Assembly style permit quiet operation and low expense on serviceability.

Ultilize of strengthen primary gear case functions in using bigger bearing has a greater load carry capacity which lowers the loss of momentum and improves the fficiency, speed, and smoothness of the primary rotor. The new primary gear case and all-metal main pulley transmission system is an efficient style to deliver the ultimate performance.

Landing skid is slanted 5 degrees forward to improve crashworthiness.

A 19mm wide Tail Boom to improves the torsional strength.
Carbon Fiber Tail Control Rod is useful and improves the helicopters tail control.

The freshly designed double point supported tail control assembly delivers slop complimentary efficiency while enhancing rudder resolution and precision.

The new tail rotor holder style includes thrust bearings which increases durability, in addition to substantially enhancing the precision and efficiency of the tail efficiency when using 78 size Tail Blades.

Standard equipment

.Microbeast PLUS Flybarless System x 1 set
.RCE-BL80X Brushless ESC x 1
.520MX Brushless Motor(1600KV/3527) x 1
.DS530 Digital servo x 3
.DS535 Digital servo x 1

Specification

.Length: 935mm
.Height: 259mm
.Width: 151mm
.Main Blade Length: 470mm
.Main Rotor Size: 1054mm
.Tail Rotor Size: 219mm
.Motor Pinion Gear: 12T
.Main Drive Gear: 134T
.Main Drive Pulley: 80T
.Tail Drive Gear: 21T
.Drive Gear Ratio: 11.17:1:3.81
.Weight(w/o battery): approx. 1400gAccessories

.T-REX 500X KIT Set x 1 
.Microbeast PLUS Flybarless System x 1 set
.470 Carbon Fiber Blades x 1
.78 Tail Rotor Blade x 1
.520MX Brushless Motor(1600KV/3527) x 1
.DS530 Digital servo x 3
.DS535 Digital servo x 1 
.RCE-BL80X Brushless ESC x 1

Radio transmitter and electronic equipment required for assembly:
.Transmitter(6-channel or more, helicopter system)
.Receiver(6-channel or more)
.6S Li-Po 2600 ~ 3300mAh (3300mAh recommendation)
.Digital Pitch Gauge